Bambu PC FR @BBL A1

Bambu Lab · PC · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pc

→

Bambu PC FR @base

→

Bambu PC FR @BBL A1

Compatible printers (3)

Bambu Lab A1 0.4 nozzle
Bambu Lab A1 0.6 nozzle
Bambu Lab A1 0.8 nozzle

Settings

Basic information

Material variant: PC inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.19 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 270 inherited
Nozzle (other layers) (°C): 280 inherited

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 20 overridden
was 60 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 12 overridden
was 2 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.94 inherited
Max volumetric speed (mm³/s): 23.2 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	100 overridden was 95	100 overridden was 95
High Temp Plate	100 overridden was 95	100 overridden was 95
Textured PEI Plate	100 overridden	100 overridden

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
compatible printers: Bambu Lab A1 0.4 nozzle, Bambu Lab A1 0.6 nozzle, Bambu Lab A1 0.8 nozzle overridden
filament id: GFC01 inherited
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
impact strength z: 8 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 260 inherited
overhang fan speed: 60 inherited
overhang fan threshold: 25% inherited
reduce fan stop start freq: 0 overridden
was 1 (inherited)
required nozzle HRC: 3 inherited
setting id: GFSC01_14 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 140 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PC"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.19"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "280"
  ],
  "overhang_fan_speed": [
    "60"
  ],
  "filament_flow_ratio": [
    "0.94"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "140"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "23.2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "260"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "filament_id": "GFC01",
  "impact_strength_z": [
    "8"
  ],
  "setting_id": "GFSC01_14",
  "compatible_printers": [
    "Bambu Lab A1 0.4 nozzle",
    "Bambu Lab A1 0.6 nozzle",
    "Bambu Lab A1 0.8 nozzle"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "name": "Bambu PC FR @BBL A1"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:18