Prusa Generic PETG @MK4S 0.8

Generic · PETG · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Prusa Generic PETG @MK4S

→

Prusa Generic PETG @MK4S 0.8

Compatible printers (1)

Prusa MK4S 0.8 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 27.82 inherited

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 230 (inherited)
Nozzle (other layers) (°C): 245 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 25 overridden
was 20 (inherited)
Fan maximum (%): 45 overridden
was 40 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 25 overridden
was 5 (inherited)
Slow down if layer below (sec): 18 overridden
was 7 (inherited)
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 22 overridden
was 12 (inherited)

Retraction

Retraction length (mm): 0.8 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	70 inherited	0 inherited
High Temp Plate	85 inherited	90 inherited
Textured PEI Plate	70 inherited	80 inherited

Custom G-code

filament_start_gcode inherited

M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Filament gcode

{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S).*/}
M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.053{elsif nozzle_diameter[filament_extruder_id]==0.5}0.042{elsif nozzle_diameter[filament_extruder_id]==0.6}0.032{elsif nozzle_diameter[filament_extruder_id]==0.8}0.018{elsif nozzle_diameter[filament_extruder_id]==0.25}0.18{elsif nozzle_diameter[filament_extruder_id]==0.3}0.1{else}0{endif} ; Filament gcode
{endif}

M142 S36 ; set heatbreak target temp

Other settings

bed type: Cool Plate inherited
compatible printers: Prusa MK4S 0.8 nozzle overridden
was Prusa MK4S 0.25 nozzle, Prusa MK4S 0.3 nozzle, Prusa MK4S 0.4 nozzle, Prusa MK4S 0.5 nozzle (inherited)
default filament colour: #FF8000 inherited
filament id: Generic PETG @MK4S 0.8 overridden
was Generic PETG @MK4S (inherited)
filament minimal purge on wipe tower: 35 inherited
filament ramming parameters: 250 100 42.4 42.4 42.4 42.4 42.4 | 0.05 42.4 0.45 42.4 0.95 42.4 1.45 42.4 1.95 42.4 2.45 42.4 2.95 42.4 3.45 42.4 3.95 42.4 4.45 42.4 4.95 42.4 inherited
filament retract before wipe: 50 overridden
was 20 (inherited)
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: 1 inherited
filament wipe distance: nil inherited
filament z hop: 0.15 inherited
filament z hop types: nil inherited
full fan speed layer: 5 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 45 overridden
was 40 (inherited)
overhang fan threshold: 95% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 80 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": "45",
  "fan_min_speed": "25",
  "filament_cost": "27.82",
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": "1",
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": "0.15",
  "hot_plate_temp": "90",
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode"
  ],
  "nozzle_temperature": "245",
  "overhang_fan_speed": "45",
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": "15",
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S).*/}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.053{elsif nozzle_diameter[filament_extruder_id]==0.5}0.042{elsif nozzle_diameter[filament_extruder_id]==0.6}0.032{elsif nozzle_diameter[filament_extruder_id]==0.8}0.018{elsif nozzle_diameter[filament_extruder_id]==0.25}0.18{elsif nozzle_diameter[filament_extruder_id]==0.3}0.1{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": "5",
  "slow_down_layer_time": "18",
  "fan_cooling_layer_time": "25",
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": "0.8",
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": "50",
  "hot_plate_temp_initial_layer": "85",
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": "22",
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": "240",
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": "35",
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "setting_id": "GFSA04",
  "filament_id": "Generic PETG @MK4S 0.8",
  "filament_notes": [
    ""
  ],
  "compatible_printers": [
    "Prusa MK4S 0.8 nozzle"
  ],
  "default_filament_colour": "#FF8000",
  "filament_ramming_parameters": [
    "250 100 42.4 42.4 42.4 42.4 42.4 | 0.05 42.4 0.45 42.4 0.95 42.4 1.45 42.4 1.95 42.4 2.45 42.4 2.95 42.4 3.45 42.4 3.95 42.4 4.45 42.4 4.95 42.4"
  ],
  "name": "Prusa Generic PETG @MK4S 0.8"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:29