Prusa Generic TPU @MK4S 0.8

Volumic · FLEX · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Prusa Generic TPU @MK4S

→

Prusa Generic TPU @MK4S 0.8

Compatible printers (2)

Prusa MK4S 0.8 nozzle
Prusa MK4S HF0.8 nozzle

Settings

Basic information

Material variant: FLEX inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.22 inherited
Cost (/kg): 82 inherited

Print temperature

Nozzle (initial layer) (°C): 230 inherited
Nozzle (other layers) (°C): 230 inherited

Cooling

Fan minimum (%): 30 inherited
Fan maximum (%): 50 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 10 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.08 inherited
Max volumetric speed (mm³/s): 9 overridden
was 3 (inherited)

Retraction

Retraction length (mm): 2.5 inherited
Retraction speed (mm/s): 60 inherited
Deretraction speed (mm/s): 20 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 inherited	40 inherited
Engineering Plate	40 inherited	40 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	40 inherited

Custom G-code

filament_start_gcode inherited

M900 K0 ; Filament gcode

M142 S36 ; set heatbreak target temp

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Prusa MK4S 0.8 nozzle, Prusa MK4S HF0.8 nozzle overridden
was Prusa MK4S 0.3 nozzle, Prusa MK4S 0.4 nozzle, Prusa MK4S 0.5 nozzle, Prusa MK4S HF0.4 nozzle, Prusa MK4S HF0.5 nozzle (inherited)
default filament colour: #008000 inherited
filament id: Generic FLEX @MK4S 0.8 overridden
was Generic FLEX @MK4S (inherited)
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: 2 inherited
filament soluble: 0 inherited
filament wipe: 0 inherited
filament wipe distance: nil inherited
filament z hop: 0 inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 210 inherited
overhang fan speed: 70 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 50 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": "50",
  "fan_min_speed": "30",
  "filament_cost": "82",
  "filament_type": [
    "FLEX"
  ],
  "filament_wipe": "0",
  "instantiation": "true",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": "0",
  "hot_plate_temp": "50",
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": "1.22",
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode"
  ],
  "nozzle_temperature": "230",
  "overhang_fan_speed": "70",
  "filament_flow_ratio": "1.08",
  "slow_down_min_speed": "15",
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "M900 K0 ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": "10",
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": "60",
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": "2.5",
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": "20",
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": "3",
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": "50",
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": "9",
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": "230",
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": "2",
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "setting_id": "GFSA04",
  "filament_id": "Generic FLEX @MK4S 0.8",
  "filament_notes": [
    ""
  ],
  "compatible_printers": [
    "Prusa MK4S 0.8 nozzle",
    "Prusa MK4S HF0.8 nozzle"
  ],
  "default_filament_colour": "#008000",
  "name": "Prusa Generic TPU @MK4S 0.8"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:29