FusRock Generic PAHT-CF @G3U 0.6 Nozzle

Volumic · PAHT-CF · 0.60mm nozzle · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Flashforge Generic PETG

→

FusRock Generic PAHT-CF @G3U 0.6 Nozzle

Compatible printers (1)

Flashforge Guider 3 Ultra 0.6 Nozzle

Inherited from this (2)

Settings

Basic information

Material variant: PAHT-CF overridden
was PETG (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.15 overridden
was 1.27 (inherited)
Cost (/kg): 300 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 295 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 295 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 15 overridden
was 80 (inherited)
Fan maximum (%): 40 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 15 overridden
was 30 (inherited)
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 12 overridden
was 30 (inherited)

Flow

Flow ratio: 0.98 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 18 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	70 inherited	0 inherited
High Temp Plate	80 overridden was 70	75 overridden was 70
Textured PEI Plate	70 inherited	80 inherited

Other settings

additional cooling fan speed: 0 overridden
was 50 (inherited)
bed type: Cool Plate inherited
compatible printers: Flashforge Guider 3 Ultra 0.6 Nozzle overridden
was Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle (inherited)
enable pressure advance: 1 inherited
filament id: GFB99 overridden
was GFG99 (inherited)
filament minimal purge on wipe tower: 5 overridden
was 15 (inherited)
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament unloading speed: 35 overridden
filament unloading speed start: 40 overridden
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 305 overridden
was 260 (inherited)
nozzle temperature range low: 290 overridden
was 220 (inherited)
overhang fan speed: 30 overridden
was 80 (inherited)
overhang fan threshold: 25% inherited
pressure advance: 0.04 overridden
was 0.046 (inherited)
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
support material interface fan speed: 30 overridden
was 90 (inherited)
temperature vitrification: 90 overridden
was 70 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "40"
  ],
  "fan_min_speed": [
    "15"
  ],
  "filament_cost": [
    "300"
  ],
  "filament_type": [
    "PAHT-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "75"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.15"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "295"
  ],
  "overhang_fan_speed": [
    "30"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "12"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    "FusRock Generic PAHT-CF @G3U 0.6 Nozzle"
  ],
  "filament_start_gcode": [
    "; filament start gcode"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "90"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "295"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "5"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "290"
  ],
  "nozzle_temperature_range_high": [
    "305"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "pressure_advance": [
    "0.04"
  ],
  "compatible_printers": [
    "Flashforge Guider 3 Ultra 0.6 Nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "support_material_interface_fan_speed": [
    "30"
  ],
  "filament_unloading_speed": [
    "35"
  ],
  "filament_unloading_speed_start": [
    "40"
  ],
  "name": "FusRock Generic PAHT-CF @G3U 0.6 Nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:28