Generic PLA @Flashforge AD4

Generic · PLA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Flashforge Generic PLA

→

Generic PLA @Flashforge AD4

Compatible printers (3)

Flashforge Adventurer 4 Series 0.3 Nozzle
Flashforge Adventurer 4 Series 0.4 Nozzle
Flashforge Adventurer 4 Series 0.6 Nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 210 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 210 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 100 (inherited)
Fan maximum (%): 60 overridden
was 100 (inherited)
Disable fan for first N layers: 2 overridden
was 1 (inherited)
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 10 overridden
was 6 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 20 (inherited)

Flow

Flow ratio: 1.07 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 20 overridden
was 25 (inherited)

Retraction

Retraction length (mm): 5 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	60 overridden was 55	60 overridden was 50
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 100 overridden
was 100 (inherited)
bed type: Cool Plate inherited
compatible printers: Flashforge Adventurer 4 Series 0.3 Nozzle, Flashforge Adventurer 4 Series 0.4 Nozzle, Flashforge Adventurer 4 Series 0.6 Nozzle overridden
was Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle (inherited)
enable pressure advance: 1 overridden
was 1 (inherited)
filament id: GFL99 overridden
was FFG01 (inherited)
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: 0 overridden
was nil (inherited)
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: 0 overridden
was nil (inherited)
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 230 overridden
was 230 (inherited)
nozzle temperature range low: 190 overridden
was 190 (inherited)
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
pressure advance: 0.8 overridden
was 0.025 (inherited)
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was FFGP01 (inherited)
slow down for layer cooling: 1 inherited
support material interface fan speed: 100 overridden
was 100 (inherited)
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "0"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1.07"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material: PLA\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "5"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "20"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "210"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "0"
  ],
  "additional_cooling_fan_speed": [
    "100"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFL99",
  "pressure_advance": [
    "0.8"
  ],
  "compatible_printers": [
    "Flashforge Adventurer 4 Series 0.3 Nozzle",
    "Flashforge Adventurer 4 Series 0.4 Nozzle",
    "Flashforge Adventurer 4 Series 0.6 Nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "support_material_interface_fan_speed": [
    "100"
  ],
  "name": "Generic PLA @Flashforge AD4"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:27