Elas ASA @base

Elas · ASA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Elas ASA @base

Inherited from this (1)

Elas ASA @System

Settings

Basic information

Material variant: ASA inherited
Vendor: Elas overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.04 overridden
was 1.24 (inherited)
Cost (/kg): 599 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 270 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 270 overridden
was 250 (inherited)
Chamber (°C): 65 overridden

Cooling

Fan minimum (%): 10 overridden
was 10 (inherited)
Fan maximum (%): 35 overridden
was 60 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 35 overridden
was 35 (inherited)
Slow down if layer below (sec): 12 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 30 (inherited)

Flow

Flow ratio: 0.95 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 15 overridden
was 20 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	110 overridden was 105	110 overridden was 105
Textured Cool Plate	40 overridden	40 overridden
Engineering Plate	100 overridden was 105	100 overridden was 105
High Temp Plate	100 overridden was 105	100 overridden was 105
Textured PEI Plate	100 overridden was 105	100 overridden was 105
Cool Plate SuperTack	35 overridden	35 overridden

Other settings

activate air filtration: 0 overridden
activate chamber temp control: 0 overridden
adaptive pressure advance: 0 overridden
adaptive pressure advance bridges: 0 overridden
adaptive pressure advance model: 0,0,0 0,0,0 overridden
adaptive pressure advance overhangs: 0 overridden
additional cooling fan speed: 0 overridden
was 0 (inherited)
bed type: Cool Plate inherited
complete print exhaust fan speed: 80 overridden
description: When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials. overridden
dont slow down outer wall: 0 overridden
during print exhaust fan speed: 60 overridden
enable overhang bridge fan: 1 overridden
enable pressure advance: 1 overridden
filament cooling final speed: 0 overridden
filament cooling initial speed: 0 overridden
filament cooling moves: 0 overridden
filament id: OGFB01 overridden
filament is support: 0 overridden
filament loading speed: 0 overridden
filament loading speed start: 0 overridden
filament long retractions when cut: nil overridden
filament minimal purge on wipe tower: 0 overridden
was 15 (inherited)
filament multitool ramming: 0 overridden
filament multitool ramming flow: 10 overridden
filament multitool ramming volume: 10 overridden
filament retract before wipe: nil overridden
was nil (inherited)
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract lift enforce: nil overridden
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction distances when cut: nil overridden
filament retraction minimum travel: nil overridden
was nil (inherited)
filament shrink: 100% overridden
filament shrinkage compensation z: 100% overridden
filament soluble: 0 overridden
was 0 (inherited)
filament stamping distance: 0 overridden
filament stamping loading speed: 0 overridden
filament toolchange delay: 0 overridden
filament unloading speed: 0 overridden
filament unloading speed start: 0 overridden
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
idle temperature: 0 overridden
instantiation: false overridden
was false (inherited)
internal bridge fan speed: -1 overridden
ironing fan speed: -1 overridden
nozzle temperature range high: 280 overridden
was 270 (inherited)
nozzle temperature range low: 240 overridden
was 240 (inherited)
overhang fan speed: 80 overridden
was 80 (inherited)
overhang fan threshold: 25% overridden
was 25% (inherited)
pellet flow coefficient: 0.4157 overridden
pressure advance: 0.075 overridden
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 0 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: -1 overridden
temperature vitrification: 100 overridden
was 110 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "35"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "599"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "110"
  ],
  "filament_vendor": [
    "Elas"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "35"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "110"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "0"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "description": "When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.",
  "filament_id": "OGFB01",
  "filament_notes": [
    ""
  ],
  "filament_shrink": [
    "100%"
  ],
  "idle_temperature": [
    "0"
  ],
  "pressure_advance": [
    "0.075"
  ],
  "ironing_fan_speed": [
    "-1"
  ],
  "chamber_temperature": [
    "65"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "supertack_plate_temp": [
    "35"
  ],
  "filament_cooling_moves": [
    "0"
  ],
  "filament_loading_speed": [
    "0"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "pellet_flow_coefficient": [
    "0.4157"
  ],
  "filament_unloading_speed": [
    "0"
  ],
  "textured_cool_plate_temp": [
    "40"
  ],
  "adaptive_pressure_advance": [
    "0"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "internal_bridge_fan_speed": [
    "-1"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_stamping_distance": [
    "0"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_cooling_final_speed": [
    "0"
  ],
  "filament_loading_speed_start": [
    "0"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "filament_cooling_initial_speed": [
    "0"
  ],
  "filament_unloading_speed_start": [
    "0"
  ],
  "adaptive_pressure_advance_model": [
    "0,0,0\n0,0,0"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "filament_stamping_loading_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "adaptive_pressure_advance_bridges": [
    "0"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_shrinkage_compensation_z": [
    "100%"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "35"
  ],
  "adaptive_pressure_advance_overhangs": [
    "0"
  ],
  "support_material_interface_fan_speed": [
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "40"
  ],
  "name": "Elas ASA @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:26