Elas PETG Basic @base

Elas · PETG · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Elas PETG Basic @base

Inherited from this (1)

Elas PETG Basic @System

Settings

Basic information

Material variant: PETG inherited
Vendor: Elas overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.27 overridden
was 1.27 (inherited)
Cost (/kg): 445 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 245 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 20 (inherited)
Fan maximum (%): 100 overridden
was 80 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 20 overridden
was 5 (inherited)
Slow down if layer below (sec): 8 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 18 overridden
was 25 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 overridden was 60	60 overridden was 60
Textured Cool Plate	40 overridden	40 overridden
Engineering Plate	80 overridden was 70	80 overridden was 0
High Temp Plate	80 overridden was 70	80 overridden was 80
Textured PEI Plate	80 overridden was 70	70 overridden was 80
Cool Plate SuperTack	70 overridden	70 overridden

Other settings

bed type: Cool Plate inherited
complete print exhaust fan speed: 80 overridden
description: To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG. overridden
dont slow down outer wall: 0 overridden
during print exhaust fan speed: 60 overridden
enable overhang bridge fan: 1 overridden
enable pressure advance: 1 overridden
filament cooling final speed: 0 overridden
filament cooling initial speed: 0 overridden
filament cooling moves: 0 overridden
filament id: OGFG00 overridden
filament is support: 0 overridden
filament loading speed: 0 overridden
filament loading speed start: 0 overridden
filament long retractions when cut: 1 overridden
filament minimal purge on wipe tower: 0 overridden
was 15 (inherited)
filament multitool ramming: 0 overridden
filament multitool ramming flow: 10 overridden
filament multitool ramming volume: 10 overridden
filament retract before wipe: nil overridden
was nil (inherited)
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract lift enforce: nil overridden
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction distances when cut: 18 overridden
filament retraction minimum travel: nil overridden
was nil (inherited)
filament shrink: 99.7% overridden
filament shrinkage compensation z: 100% overridden
filament soluble: 0 overridden
was 0 (inherited)
filament stamping distance: 0 overridden
filament stamping loading speed: 0 overridden
filament toolchange delay: 0 overridden
filament unloading speed: 0 overridden
filament unloading speed start: 0 overridden
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
idle temperature: 0 overridden
instantiation: false overridden
was false (inherited)
internal bridge fan speed: -1 overridden
ironing fan speed: -1 overridden
nozzle temperature range high: 270 overridden
was 280 (inherited)
nozzle temperature range low: 230 overridden
was 220 (inherited)
overhang fan speed: 100 overridden
was 70 (inherited)
overhang fan threshold: 10% overridden
was 95% (inherited)
pellet flow coefficient: 0.4157 overridden
pressure advance: 0.035 overridden
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 3 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: -1 overridden
temperature vitrification: 70 overridden
was 80 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "445"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "80"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Elas"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "textured_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "0"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "description": "To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG.",
  "filament_id": "OGFG00",
  "filament_notes": [
    ""
  ],
  "filament_shrink": [
    "99.7%"
  ],
  "idle_temperature": [
    "0"
  ],
  "pressure_advance": [
    "0.035"
  ],
  "ironing_fan_speed": [
    "-1"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "supertack_plate_temp": [
    "70"
  ],
  "filament_cooling_moves": [
    "0"
  ],
  "filament_loading_speed": [
    "0"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "pellet_flow_coefficient": [
    "0.4157"
  ],
  "filament_unloading_speed": [
    "0"
  ],
  "textured_cool_plate_temp": [
    "40"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "internal_bridge_fan_speed": [
    "-1"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_stamping_distance": [
    "0"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_cooling_final_speed": [
    "0"
  ],
  "filament_loading_speed_start": [
    "0"
  ],
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "filament_cooling_initial_speed": [
    "0"
  ],
  "filament_unloading_speed_start": [
    "0"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "filament_stamping_loading_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_shrinkage_compensation_z": [
    "100%"
  ],
  "filament_long_retractions_when_cut": [
    "1"
  ],
  "supertack_plate_temp_initial_layer": [
    "70"
  ],
  "support_material_interface_fan_speed": [
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "18"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "40"
  ],
  "name": "Elas PETG Basic @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:26