COEX TPE 30D @base

COEX 3D · TPU · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

COEX TPE 30D @base

Inherited from this (1)

COEX TPE 30D @System

Settings

Basic information

Material variant: TPU overridden
was TPU (inherited)
Vendor: COEX 3D overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.15 overridden
was 1.24 (inherited)
Cost (/kg): 80.00 overridden
was 35 (inherited)

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 235 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 235 (inherited)

Cooling

Fan minimum (%): 80 overridden
was 100 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 10 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 5 overridden
was 5 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 3.5 overridden
was 15 (inherited)

Retraction

Retraction length (mm): 0.4 overridden
was nil (inherited)
Retraction speed (mm/s): 20 overridden
was nil (inherited)
Deretraction speed (mm/s): 20 overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 inherited	40 inherited
Engineering Plate	40 inherited	40 inherited
High Temp Plate	40 inherited	40 inherited
Textured PEI Plate	50 inherited	40 inherited

Other settings

additional cooling fan speed: 0 inherited
bed temperature: 30 overridden
bed temperature initial layer: 35 overridden
bed type: Cool Plate inherited
disable fan first layers: 1 overridden
enable pressure advance: 0 overridden
filament id: CX30DB20 overridden
filament minimal purge on wipe tower: 15 inherited
filament notes: Flexible filament - print slowly with minimal retraction overridden
filament retract before wipe: 0% overridden
was nil (inherited)
filament retract layer change: 0 overridden
filament retract restart extra: nil inherited
filament retract when changing layer: 0 overridden
was nil (inherited)
filament retraction minimum travel: 3 overridden
was nil (inherited)
filament soluble: 0 inherited
filament wipe: 0 overridden
was nil (inherited)
filament wipe distance: 0 overridden
was nil (inherited)
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 2 overridden
was 0 (inherited)
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 210 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 60 overridden
was 50 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "80"
  ],
  "filament_cost": [
    "80.00"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "0"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "40"
  ],
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "COEX 3D"
  ],
  "filament_density": [
    "1.15"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "2"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "0"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "20"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "20"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "0%"
  ],
  "hot_plate_temp_initial_layer": [
    "40"
  ],
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": [
    "3.5"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "0"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "filament_id": "CX30DB20",
  "filament_notes": "Flexible filament - print slowly with minimal retraction",
  "bed_temperature": [
    "30"
  ],
  "compatible_prints": [],
  "compatible_printers": [],
  "enable_pressure_advance": [
    "0"
  ],
  "disable_fan_first_layers": [
    "1"
  ],
  "compatible_prints_condition": "",
  "bed_temperature_initial_layer": [
    "35"
  ],
  "compatible_printers_condition": "",
  "filament_retract_layer_change": [
    "0"
  ],
  "name": "COEX TPE 30D @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:25