COEX PLA PRIME @base

COEX 3D · PLA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

COEX PLA PRIME @base

Inherited from this (1)

COEX PLA PRIME @System

Settings

Basic information

Material variant: PLA overridden
was PLA (inherited)
Vendor: COEX 3D overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 overridden
was 1.24 (inherited)
Cost (/kg): 32.00 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 235 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 100 overridden
was 100 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 5 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 15 overridden
was 20 (inherited)

Retraction

Retraction length (mm): 1.2 overridden
was nil (inherited)
Retraction speed (mm/s): 50 overridden
was nil (inherited)
Deretraction speed (mm/s): 40 overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 0 inherited
bed temperature: 60 overridden
bed temperature initial layer: 60 overridden
bed type: Cool Plate inherited
disable fan first layers: 1 overridden
filament id: CXPLAB08 overridden
filament minimal purge on wipe tower: 15 inherited
filament notes: Made with NatureWorks Ingeo 3D850 - improved heat resistance and toughness overridden
filament retract before wipe: 70% overridden
was nil (inherited)
filament retract layer change: 1 overridden
filament retract restart extra: nil inherited
filament retract when changing layer: 1 overridden
was nil (inherited)
filament retraction minimum travel: 2 overridden
was nil (inherited)
filament soluble: 0 inherited
filament wipe: 1 overridden
was nil (inherited)
filament wipe distance: 2 overridden
was nil (inherited)
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 3 overridden
was 0 (inherited)
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 60 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "32.00"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "1"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "COEX 3D"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "235"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "2"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "50"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "1.2"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "40"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "70%"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "2"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "filament_id": "CXPLAB08",
  "filament_notes": "Made with NatureWorks Ingeo 3D850 - improved heat resistance and toughness",
  "bed_temperature": [
    "60"
  ],
  "compatible_prints": [],
  "compatible_printers": [],
  "disable_fan_first_layers": [
    "1"
  ],
  "compatible_prints_condition": "",
  "bed_temperature_initial_layer": [
    "60"
  ],
  "compatible_printers_condition": "",
  "filament_retract_layer_change": [
    "1"
  ],
  "name": "COEX PLA PRIME @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:25