Valment PLA Silk @base

Valment · PLA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Valment PLA Silk @base

Inherited from this (1)

Valment PLA Silk @System

Settings

Basic information

Material variant: PLA overridden
was PLA (inherited)
Vendor: Valment overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 overridden
was 1.24 (inherited)
Cost (/kg): 710 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 245 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 6 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 5 (inherited)

Flow

Flow ratio: 0.98 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 7.5 overridden
was 20 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 100 overridden
was 0 (inherited)
bed type: Cool Plate inherited
complete print exhaust fan speed: 80 overridden
default filament colour: #124943 overridden
during print exhaust fan speed: 60 overridden
filament id: VLMNT02 overridden
filament minimal purge on wipe tower: 15 inherited
filament notes: Bu filament ayarları GlauTech tarafından oluşturulmuştur. Filamentin daha verimli çalışması için, slicerdaki kalibrasyon ayarlarının tek tek yapılması önemlidir. Kalibrasyon ayarları için, GlauTech youtube kanalından destek alabilirsiniz. Boş Makara Ağırlığı: 150gr overridden
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 250 overridden
was 230 (inherited)
nozzle temperature range low: 220 overridden
was 190 (inherited)
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "710"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Valment"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "6"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "7.5"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "100"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "filament_id": "VLMNT02",
  "filament_notes": [
    "Bu filament ayarlar\u0131 GlauTech taraf\u0131ndan olu\u015fturulmu\u015ftur. Filamentin daha verimli \u00e7al\u0131\u015fmas\u0131 i\u00e7in, slicerdaki kalibrasyon ayarlar\u0131n\u0131n tek tek yap\u0131lmas\u0131 \u00f6nemlidir. Kalibrasyon ayarlar\u0131 i\u00e7in, GlauTech youtube kanal\u0131ndan destek alabilirsiniz.\n\nBo\u015f Makara A\u011f\u0131rl\u0131\u011f\u0131: 150gr"
  ],
  "default_filament_colour": [
    "#124943"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "name": "Valment PLA Silk @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:24