QIDI ASA @Qidi X-Plus 4 0.2 nozzle

Generic · ASA · 0.20mm nozzle · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

QIDI ASA @Qidi

→

QIDI ASA @Qidi X-Plus 4 0.2 nozzle

Compatible printers (1)

Qidi X-Plus 4 0.2 nozzle

Settings

Basic information

Material variant: ASA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.07 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 250 inherited
Nozzle (other layers) (°C): 255 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 80 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 35 inherited
Slow down if layer below (sec): 3 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.92 inherited
Max volumetric speed (mm³/s): 2 overridden
was 16 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	90 inherited	90 inherited
Engineering Plate	90 inherited	90 inherited
High Temp Plate	90 inherited	90 inherited
Textured PEI Plate	90 inherited	90 inherited

Other settings

additional fan full speed layer: 0 inherited
chamber temperatures: 0 overridden
close additional fan first x layers: 3 inherited
compatible printers: Qidi X-Plus 4 0.2 nozzle overridden
was Qidi X-Plus 0.4 nozzle, Qidi X-Max 0.4 nozzle, Qidi X-CF Pro 0.4 nozzle, Qidi X-Smart 3 0.4 nozzle, Qidi X-Plus 3 0.4 nozzle, Qidi X-Max 3 0.4 nozzle, Qidi X-CF Pro 0.8 nozzle (inherited)
enable pressure advance: 1 inherited
filament id: GFB01 overridden
was GFB01 (inherited)
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 80 inherited
overhang fan threshold: 25% inherited
pressure advance: 0.03 overridden
was 0.021 (inherited)
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
setting id: GFSB01_Qidi_10 overridden
was GFSB01_Qidi_00 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "90"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "90"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.07"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "0.92"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "3"
  ],
  "fan_cooling_layer_time": [
    "35"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "90"
  ],
  "filament_max_volumetric_speed": [
    "2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "GFSB01_Qidi_10",
  "filament_id": "GFB01",
  "pressure_advance": [
    "0.03"
  ],
  "compatible_printers": [
    "Qidi X-Plus 4 0.2 nozzle"
  ],
  "textured_plate_temp": [
    "90"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "textured_plate_temp_initial_layer": [
    "90"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "name": "QIDI ASA @Qidi X-Plus 4 0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:18