InfiMech PLA Hyper

FlyingBear · PLA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla_Hyper

→

InfiMech PLA Hyper

Compatible printers (1)

InfiMech TX 0.4 nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: InfiMech inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 220 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 8 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.94 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 25 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	60 inherited	60 inherited
Textured PEI Plate	60 inherited	60 inherited

Other settings

additional cooling fan speed: 100 inherited
bed type: Cool Plate inherited
compatible printers: InfiMech TX 0.4 nozzle overridden
enable pressure advance: 1 overridden
filament id: GFL99 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
pressure advance: 0.02 overridden
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "InfiMech"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.94"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "25"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "100"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFL99",
  "pressure_advance": [
    "0.02"
  ],
  "compatible_printers": [
    "InfiMech TX 0.4 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "name": "InfiMech PLA Hyper"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:24