Anycubic PLA @Anycubic Kobra 3 0.6 nozzle

Anycubic · PLA · 0.60mm nozzle · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Anycubic Generic PLA

→

Anycubic PLA @Anycubic Kobra 3 0.6 nozzle

Compatible printers (1)

Anycubic Kobra 3 0.6 nozzle

Settings

Basic information

Material variant: PLA overridden
was PLA (inherited)
Vendor: Anycubic overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.24 overridden
was 1.24 (inherited)
Cost (/kg): 20 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 215 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 205 overridden
was 220 (inherited)
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 60 overridden
was 100 (inherited)
Fan maximum (%): 80 overridden
was 100 (inherited)
Disable fan for first N layers: 1 overridden
was 1 (inherited)
Full fan if layer below (sec): 80 overridden
was 100 (inherited)
Slow down if layer below (sec): 8 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 5 (inherited)

Flow

Flow ratio: 0.98 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 overridden was 50	35 overridden was 50
Engineering Plate	0 overridden was 50	0 overridden was 50
High Temp Plate	65 overridden was 50	65 overridden was 50
Textured PEI Plate	45 overridden was 50	45 overridden was 50

Other settings

activate air filtration: 0 overridden
activate chamber temp control: 0 overridden
additional cooling fan speed: 70 overridden
was 0 (inherited)
bed type: Cool Plate overridden
was Cool Plate (inherited)
compatible printers: Anycubic Kobra 3 0.6 nozzle overridden
was Anycubic i3 Mega S 0.4 nozzle, Anycubic Chiron 0.4 nozzle, Anycubic Vyper 0.4 nozzle, Anycubic Kobra 0.4 nozzle, Anycubic Kobra Max 0.4 nozzle, Anycubic Kobra Plus 0.4 nozzle, Anycubic 4Max Pro 0.4 nozzle, Anycubic 4Max Pro 2 0.4 nozzle, Anycubic Kobra 2 0.4 nozzle, Anycubic Kobra 3 0.2 nozzle, Anycubic Kobra 3 0.4 nozzle, Anycubic Kobra 3 0.6 nozzle, Anycubic Kobra 3 0.8 nozzle (inherited)
complete print exhaust fan speed: 80 overridden
during print exhaust fan speed: 60 overridden
enable overhang bridge fan: 1 overridden
enable pressure advance: 0 overridden
filament cooling final speed: 0 overridden
filament cooling initial speed: 0 overridden
filament cooling moves: 0 overridden
filament id: GFL99 overridden
was GFL99 (inherited)
filament is support: 0 overridden
filament load time: 0 overridden
filament loading speed: 0 overridden
filament loading speed start: 0 overridden
filament long retractions when cut: nil overridden
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament multitool ramming: 0 overridden
filament multitool ramming flow: 10 overridden
filament multitool ramming volume: 10 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament retract before wipe: nil overridden
was nil (inherited)
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract lift enforce: nil overridden
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction distances when cut: nil overridden
filament retraction minimum travel: nil overridden
was nil (inherited)
filament shrink: 100% overridden
filament soluble: 0 overridden
was 0 (inherited)
filament toolchange delay: 0 overridden
filament unload time: 0 overridden
filament unloading speed: 0 overridden
filament unloading speed start: 0 overridden
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 3 overridden
was 0 (inherited)
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 230 overridden
was 230 (inherited)
nozzle temperature range low: 190 overridden
was 190 (inherited)
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 50% overridden
was 50% (inherited)
pressure advance: 0.05 overridden
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 0 overridden
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: -1 overridden
temperature vitrification: 60 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "60"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "65"
  ],
  "cool_plate_temp": [
    "35"
  ],
  "filament_vendor": [
    "Anycubic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "205"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "45"
  ],
  "filament_settings_id": [
    "Anycubic PLA @Anycubic Kobra 3 0.6 nozzle"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "80"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "65"
  ],
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "215"
  ],
  "textured_plate_temp_initial_layer": [
    "45"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFL99",
  "compatible_printers": [
    "Anycubic Kobra 3 0.6 nozzle"
  ],
  "filament_notes": [
    ""
  ],
  "filament_shrink": [
    "100%"
  ],
  "pressure_advance": [
    "0.05"
  ],
  "compatible_prints": [],
  "filament_load_time": [
    "0"
  ],
  "chamber_temperature": [
    "0"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "filament_unload_time": [
    "0"
  ],
  "filament_cooling_moves": [
    "0"
  ],
  "filament_loading_speed": [
    "0"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "filament_unloading_speed": [
    "0"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "compatible_prints_condition": "",
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_cooling_final_speed": [
    "0"
  ],
  "filament_loading_speed_start": [
    "0"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "compatible_printers_condition": "",
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "filament_cooling_initial_speed": [
    "0"
  ],
  "filament_unloading_speed_start": [
    "0"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "support_material_interface_fan_speed": [
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "name": "Anycubic PLA @Anycubic Kobra 3 0.6 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:24