WonderMaker ABS

WonderMaker · ABS · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

WonderMaker ABS

Compatible printers (8)

WonderMaker ZR 0.2 nozzle
WonderMaker ZR 0.4 nozzle
WonderMaker ZR 0.6 nozzle
WonderMaker ZR 0.8 nozzle
WonderMaker ZR Ultra 0.2 nozzle
WonderMaker ZR Ultra 0.4 nozzle
WonderMaker ZR Ultra 0.6 nozzle
WonderMaker ZR Ultra 0.8 nozzle

Inherited from this (1)

WonderMaker ABS @WonderMaker ZR Ultra S

Settings

Basic information

Material variant: ABS inherited
Vendor: WonderMaker overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 24.99 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 250 inherited
Nozzle (other layers) (°C): 250 inherited

Cooling

Fan minimum (%): 18 inherited
Fan maximum (%): 60 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 5 inherited
Slow down if layer below (sec): 3 inherited
Min speed when slowed (mm/s): 30 inherited

Flow

Flow ratio: 0.95 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 20 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	105 inherited	105 inherited
Textured PEI Plate	105 inherited	105 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: WonderMaker ZR 0.2 nozzle, WonderMaker ZR 0.4 nozzle, WonderMaker ZR 0.6 nozzle, WonderMaker ZR 0.8 nozzle, WonderMaker ZR Ultra 0.2 nozzle, WonderMaker ZR Ultra 0.4 nozzle, WonderMaker ZR Ultra 0.6 nozzle, WonderMaker ZR Ultra 0.8 nozzle overridden
description: When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials. overridden
filament id: GFB00 overridden
filament minimal purge on wipe tower: 15 inherited
filament multitool ramming: 1 overridden
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 40 inherited
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "18"
  ],
  "filament_cost": [
    "24.99"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "WonderMaker"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "40"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "3"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "20"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "description": "When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.",
  "filament_id": "GFB00",
  "compatible_printers": [
    "WonderMaker ZR 0.2 nozzle",
    "WonderMaker ZR 0.4 nozzle",
    "WonderMaker ZR 0.6 nozzle",
    "WonderMaker ZR 0.8 nozzle",
    "WonderMaker ZR Ultra 0.2 nozzle",
    "WonderMaker ZR Ultra 0.4 nozzle",
    "WonderMaker ZR Ultra 0.6 nozzle",
    "WonderMaker ZR Ultra 0.8 nozzle"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "name": "WonderMaker ABS"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:23