Snapmaker PETG @U1 base

Generic · PETG · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_petg

→

Snapmaker PETG @U1 base

Inherited from this (1)

Snapmaker PETG @U1

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 overridden
was 1.24 (inherited)
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 245 (inherited)
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 0 overridden
was 20 (inherited)
Fan maximum (%): 20 overridden
was 80 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 30 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 20 inherited

Retraction

Retraction length (mm): 1.0 inherited
Retraction speed (mm/s): 35 overridden
was nil (inherited)
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	70 inherited	70 inherited
Engineering Plate	70 inherited	70 inherited
High Temp Plate	70 inherited	70 inherited
Textured PEI Plate	70 inherited	70 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
filament cooling final speed: 60 overridden
filament cooling initial speed: 35 overridden
filament cooling moves: 2 overridden
filament id: 22090010620 overridden
filament load time: 2 overridden
filament loading speed: 35 overridden
filament loading speed start: 35 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament unload time: 2 overridden
filament unloading speed: 35 overridden
filament unloading speed start: 35 overridden
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.0 inherited
filament z hop types: Spiral Lift overridden
was nil (inherited)
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 255 inherited
nozzle temperature range low: 240 overridden
was 210 (inherited)
overhang fan speed: 25 overridden
was 70 (inherited)
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 178 overridden
was 70 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "70"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    ""
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "25"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "Spiral Lift"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "35"
  ],
  "temperature_vitrification": [
    "178"
  ],
  "filament_retraction_length": [
    "1.0"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "70"
  ],
  "filament_max_volumetric_speed": [
    "20"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "255"
  ],
  "filament_id": "22090010620",
  "filament_load_time": [
    "2"
  ],
  "filament_unload_time": [
    "2"
  ],
  "filament_cooling_moves": [
    "2"
  ],
  "filament_loading_speed": [
    "35"
  ],
  "filament_unloading_speed": [
    "35"
  ],
  "filament_cooling_final_speed": [
    "60"
  ],
  "filament_loading_speed_start": [
    "35"
  ],
  "filament_cooling_initial_speed": [
    "35"
  ],
  "filament_unloading_speed_start": [
    "35"
  ],
  "name": "Snapmaker PETG @U1 base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:22