Snapmaker TPU 95A @U1 base

Generic · TPU · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inherited from this (1)

Snapmaker TPU 95A @U1

Settings

Basic information

Material variant: TPU overridden
Vendor: Generic overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 1.24 overridden
Cost (/kg): 20 overridden

Print temperature

Nozzle (initial layer) (°C): 240 overridden
Nozzle (other layers) (°C): 240 overridden

Cooling

Fan minimum (%): 100 overridden
Fan maximum (%): 100 overridden
Disable fan for first N layers: 1 overridden
Full fan if layer below (sec): 100 overridden
Slow down if layer below (sec): 8 overridden
Min speed when slowed (mm/s): 10 overridden

Flow

Flow ratio: 1 overridden
Max volumetric speed (mm³/s): 15 overridden

Retraction

Retraction length (mm): 0.4 overridden
Retraction speed (mm/s): nil overridden
Deretraction speed (mm/s): nil overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	30 overridden	30 overridden
Engineering Plate	30 overridden	30 overridden
High Temp Plate	35 overridden	35 overridden
Textured PEI Plate	35 overridden	35 overridden

Other settings

additional cooling fan speed: 70 overridden
bed type: Cool Plate overridden
filament id: 297165629001 overridden
filament minimal purge on wipe tower: 15 overridden
filament retract before wipe: nil overridden
filament retract restart extra: nil overridden
filament retract when changing layer: nil overridden
filament retraction minimum travel: nil overridden
filament soluble: 0 overridden
filament wipe: nil overridden
filament wipe distance: nil overridden
filament z hop: nil overridden
filament z hop types: nil overridden
full fan speed layer: 0 overridden
instantiation: false overridden
nozzle temperature range high: 250 overridden
nozzle temperature range low: 200 overridden
overhang fan speed: 100 overridden
overhang fan threshold: 95% overridden
reduce fan stop start freq: 1 overridden
slow down for layer cooling: 1 overridden
temperature vitrification: 60 overridden

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "filament_id": "297165629001",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "30"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "35"
  ],
  "cool_plate_temp": [
    "30"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "35"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "30"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "35"
  ],
  "nozzle_temperature_range_low": [
    "200"
  ],
  "cool_plate_temp_initial_layer": [
    "30"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "35"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "name": "Snapmaker TPU 95A @U1 base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:21