MM Generic PEEK

Generic · PEEK · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_peek

→

MM Generic PEEK

Compatible printers (2)

MM BoneKing 0.4 nozzle
MM hj SK 0.4 nozzle

Settings

Basic information

Material variant: PEEK inherited
Vendor: Generic inherited
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.04 inherited
Cost (/kg): 1000 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 420 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 420 overridden
was 260 (inherited)

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 40 overridden
was 80 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 35 inherited
Slow down if layer below (sec): 3 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 10 overridden
was 28.6 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	60 overridden was 105	60 overridden was 105
Textured PEI Plate	105 inherited	105 inherited

Other settings

bed type: Cool Plate inherited
compatible printers: MM hj SK 0.4 nozzle, MM BoneKing 0.4 nozzle overridden
filament id: GFG99 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 5 overridden
was 0 (inherited)
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 460 overridden
was 270 (inherited)
nozzle temperature range low: 380 overridden
was 240 (inherited)
overhang fan speed: 80 inherited
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 340 overridden
was 110 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "40"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "1000"
  ],
  "filament_type": [
    "PEEK"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "420"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "5"
  ],
  "slow_down_layer_time": [
    "3"
  ],
  "fan_cooling_layer_time": [
    "35"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "340"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "420"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "380"
  ],
  "nozzle_temperature_range_high": [
    "460"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFG99",
  "compatible_printers": [
    "MM hj SK 0.4 nozzle",
    "MM BoneKing 0.4 nozzle"
  ],
  "name": "MM Generic PEEK"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:21