Ginger Generic PLA

Generic · PLA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

Ginger Generic PLA

Compatible printers (4)

Ginger G1 1.2 nozzle
Ginger G1 3.0 nozzle
Ginger G1 5.0 nozzle
Ginger G1 8.0 nozzle

Settings

Basic information

Material variant: PLA overridden
was PLA (inherited)
Vendor: Generic overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 overridden
was 0 (inherited)
Cost (/kg): 6 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 200 inherited
Nozzle (other layers) (°C): 200 inherited

Cooling

Fan minimum (%): 0 overridden
was 35 (inherited)
Fan maximum (%): 0 overridden
was 100 (inherited)
Disable fan for first N layers: 4 overridden
was 3 (inherited)
Full fan if layer below (sec): 100 overridden
was 60 (inherited)
Slow down if layer below (sec): 50 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 1 overridden
was 10 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 250 overridden
was 0 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	50 overridden was 60	50 overridden was 60
Textured PEI Plate	60 inherited	60 inherited

Custom G-code

filament_start_gcode overridden

SET_PRESSURE_ADVANCE EXTRUDER=extruder SMOOTH_TIME=0.5

Other settings

bed type: Cool Plate inherited
compatible printers: Ginger G1 1.2 nozzle, Ginger G1 3.0 nozzle, Ginger G1 5.0 nozzle, Ginger G1 8.0 nozzle overridden
enable overhang bridge fan: 0 overridden
enable pressure advance: 1 overridden
extruder rotation volume: 456 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil overridden
was nil (inherited)
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract lift enforce: nil overridden
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction minimum travel: nil overridden
was nil (inherited)
filament soluble: 0 inherited
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
mixing stepper rotation volume: 8000 overridden
multi zone 1 initial layer: 200 overridden
multi zone 1 temperature: 200 overridden
multi zone 2 initial layer: 200 overridden
multi zone 2 temperature: 200 overridden
multi zone 3 initial layer: 200 overridden
multi zone 3 temperature: 200 overridden
nozzle temperature range high: 220 overridden
nozzle temperature range low: 180 overridden
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 50% overridden
was 95% (inherited)
pressure advance: 0.3 overridden
reduce fan stop start freq: 0 overridden
was 0 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 55 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "0"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "6"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "200"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "1"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    "PLA"
  ],
  "filament_start_gcode": [
    "SET_PRESSURE_ADVANCE EXTRUDER=extruder SMOOTH_TIME=0.5"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "50"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "55"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "250"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "200"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "pressure_advance": [
    "0.3"
  ],
  "compatible_printers": [
    "Ginger G1 1.2 nozzle",
    "Ginger G1 3.0 nozzle",
    "Ginger G1 5.0 nozzle",
    "Ginger G1 8.0 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "extruder_rotation_volume": "456",
  "multi_zone_1_temperature": "200",
  "multi_zone_2_temperature": "200",
  "multi_zone_3_temperature": "200",
  "enable_overhang_bridge_fan": [
    "0"
  ],
  "multi_zone_1_initial_layer": "200",
  "multi_zone_2_initial_layer": "200",
  "multi_zone_3_initial_layer": "200",
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "180"
  ],
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "nozzle_temperature_range_high": [
    "220"
  ],
  "mixing_stepper_rotation_volume": "8000",
  "name": "Ginger Generic PLA"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:21