Generic PPS-CF @base

Generic · PPS-CF · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pps

→

Generic PPS-CF @base

Inherited from this (1)

Generic PPS-CF @BBL X1E

Settings

Basic information

Material variant: PPS-CF overridden
was PPS (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.26 overridden
was 1.36 (inherited)
Cost (/kg): 240 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 320 inherited
Nozzle (other layers) (°C): 320 inherited

Cooling

Fan minimum (%): 0 inherited
Fan maximum (%): 30 overridden
was 50 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 5 inherited
Slow down if layer below (sec): 2 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.96 inherited
Max volumetric speed (mm³/s): 3 overridden
was 4 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	110 inherited	110 inherited
High Temp Plate	110 inherited	110 inherited
Textured PEI Plate	110 inherited	110 inherited
Cool Plate SuperTack	0 inherited	0 inherited

Other settings

bed type: Cool Plate inherited
chamber temperatures: 60 inherited
description: When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials. overridden
filament id: GFT98 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 340 inherited
nozzle temperature range low: 310 overridden
was 300 (inherited)
overhang fan speed: 30 inherited
overhang fan threshold: 0% inherited
reduce fan stop start freq: 0 inherited
required nozzle HRC: 40 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 220 overridden
was 125 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "240"
  ],
  "filament_type": [
    "PPS-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "110"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "110"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.26"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "320"
  ],
  "overhang_fan_speed": [
    "30"
  ],
  "filament_flow_ratio": [
    "0.96"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "110"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "220"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "110"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "110"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "3"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "320"
  ],
  "textured_plate_temp_initial_layer": [
    "110"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "chamber_temperatures": [
    "60"
  ],
  "supertack_plate_temp": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "310"
  ],
  "nozzle_temperature_range_high": [
    "340"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "description": "When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.",
  "filament_id": "GFT98",
  "required_nozzle_HRC": [
    "40"
  ],
  "name": "Generic PPS-CF @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:18