Generic PETG

Generic · PETG · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Generic PETG @base

→

Generic PETG

Compatible printers (12)

Bambu Lab P1S 0.4 nozzle
Bambu Lab P1S 0.6 nozzle
Bambu Lab P1S 0.8 nozzle
Bambu Lab X1 0.4 nozzle
Bambu Lab X1 0.6 nozzle
Bambu Lab X1 0.8 nozzle
Bambu Lab X1 Carbon 0.4 nozzle
Bambu Lab X1 Carbon 0.6 nozzle
Bambu Lab X1 Carbon 0.8 nozzle
Bambu Lab X1E 0.4 nozzle
Bambu Lab X1E 0.6 nozzle
Bambu Lab X1E 0.8 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 255 inherited
Nozzle (other layers) (°C): 255 inherited

Cooling

Fan minimum (%): 40 inherited
Fan maximum (%): 90 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 12 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 12 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	70 inherited	70 inherited
High Temp Plate	70 inherited	70 inherited
Textured PEI Plate	70 inherited	70 inherited

Custom G-code

filament_start_gcode inherited

; filament start gcode
{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255
{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180
{endif}

{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

Other settings

bed type: Cool Plate inherited
compatible printers: Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 0.4 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab X1 0.6 nozzle, Bambu Lab X1 0.8 nozzle, Bambu Lab P1S 0.4 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1E 0.4 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle overridden
filament id: GFG99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 90 inherited
overhang fan threshold: 10% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSG99 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 80 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "90"
  ],
  "fan_min_speed": [
    "40"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255\n{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "filament_id": "GFG99",
  "setting_id": "GFSG99",
  "compatible_printers": [
    "Bambu Lab X1 Carbon 0.4 nozzle",
    "Bambu Lab X1 0.4 nozzle",
    "Bambu Lab X1 Carbon 0.6 nozzle",
    "Bambu Lab X1 Carbon 0.8 nozzle",
    "Bambu Lab X1 0.6 nozzle",
    "Bambu Lab X1 0.8 nozzle",
    "Bambu Lab P1S 0.4 nozzle",
    "Bambu Lab P1S 0.6 nozzle",
    "Bambu Lab P1S 0.8 nozzle",
    "Bambu Lab X1E 0.4 nozzle",
    "Bambu Lab X1E 0.6 nozzle",
    "Bambu Lab X1E 0.8 nozzle"
  ],
  "name": "Generic PETG"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:17