Bambu TPU 95A HF @base

Bambu Lab · TPU · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Bambu TPU 95A HF @base

Inherited from this (8)

Settings

Basic information

Material variant: TPU inherited
Vendor: Bambu Lab overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.22 overridden
was 1.24 (inherited)
Cost (/kg): 41.99 overridden
was 35 (inherited)

Print temperature

Nozzle (initial layer) (°C): 230 overridden
was 235 (inherited)
Nozzle (other layers) (°C): 230 overridden
was 235 (inherited)

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 5 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 12 overridden
was 15 (inherited)

Retraction

Retraction length (mm): 0.8 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 inherited	40 inherited
Engineering Plate	40 inherited	40 inherited
High Temp Plate	40 inherited	40 inherited
Textured PEI Plate	50 inherited	40 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
description: This filament is too soft and not compatible with the AMS. Printing it is of many requirements, and to get better printing quality, please refer to this wiki: TPU printing guide. overridden
filament id: OGFU00 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 210 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 50 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "41.99"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "40"
  ],
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.22"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": [
    "0.8"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "40"
  ],
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "description": "This filament is too soft and not compatible with the AMS. Printing it is of many requirements, and to get better printing quality, please refer to this wiki: TPU printing guide.",
  "filament_id": "OGFU00",
  "name": "Bambu TPU 95A HF @base"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 12:25
v1 created 2026-05-19 12:16