Elegoo PAHT @base

Elegoo · PA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

Elegoo PAHT @base

Inherited from this (3)

Settings

Basic information

Material variant: PA inherited
Vendor: Elegoo overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 overridden
was 1.04 (inherited)
Cost (/kg): 0 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 270 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 50 overridden
was 0 (inherited)
Fan maximum (%): 60 inherited
Disable fan for first N layers: 1 overridden
was 3 (inherited)
Full fan if layer below (sec): 80 overridden
was 10 (inherited)
Slow down if layer below (sec): 8 overridden
was 2 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 16 overridden
was 8 (inherited)

Retraction

Retraction length (mm): 1.0 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 overridden was 0	35 overridden was 0
Engineering Plate	0 overridden was 100	0 overridden was 100
High Temp Plate	60 overridden was 100	60 overridden was 100
Textured PEI Plate	60 overridden was 100	60 overridden was 100

Other settings

additional cooling fan speed: 0 overridden
bed type: Cool Plate inherited
filament id: EPAHTB00 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.0 inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 240 overridden
was 300 (inherited)
nozzle temperature range low: 190 overridden
was 260 (inherited)
overhang fan speed: 60 inherited
overhang fan threshold: 50% overridden
was 95% (inherited)
reduce fan stop start freq: 1 overridden
was 0 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 45 overridden
was 108 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "50"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "35"
  ],
  "filament_vendor": [
    "Elegoo"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "60"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "80"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "45"
  ],
  "filament_retraction_length": [
    "1.0"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "16"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "240"
  ],
  "filament_id": "EPAHTB00",
  "additional_cooling_fan_speed": [
    "0"
  ],
  "name": "Elegoo PAHT @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:15