Overture PLA @X-Plus 4 0.4 nozzle

Overture · PLA · by qidi-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*Overture PLA*

→

Overture PLA @X-Plus 4 0.4 nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: Overture inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.2 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 210 inherited
Nozzle (other layers) (°C): 210 overridden
was 220 (inherited)
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 60 inherited
Slow down if layer below (sec): 10 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 1 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 11 overridden
was 20 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 inherited	60 inherited

Other settings

advance pressure: 0.037 overridden
was 0.031 (inherited)
box temperature: 0 inherited
bridge fan speed: 100 inherited
chamber minimal temperature: 0 inherited
compatible printers condition: printer_model=="X-Plus 4" and nozzle_diameter[0]==0.4 overridden
was — (inherited)
cooling: 1 inherited
disable rapid cooling fan first layers: 3 inherited
dont slow down outer wall: 0 inherited
enable advance pressure: 1 inherited
enable auxiliary fan: 100 inherited
enable auxiliary fan unseal: 0 inherited
enable dynamic fan speeds: 0 inherited
enable volume fan: 100 inherited
end filament gcode: ; Filament-specific end gcode ;END gcode for filament inherited
fan always on: 1 inherited
filament colour: #3399FF inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 0 inherited
filament deretract speed: nil inherited
filament flush temp: 240 inherited
filament infill max crossing speed: 0 inherited
filament infill max speed: 0 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament multitool ramming: 0 inherited
filament multitool ramming flow: 10 inherited
filament multitool ramming volume: 10 inherited
filament purge multiplier: 100 inherited
filament ramming parameters: 120 100| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: nil inherited
filament retract before wipe: nil inherited
filament retract layer change: nil inherited
filament retract length: nil inherited
filament retract lift: nil inherited
filament retract lift above: nil inherited
filament retract lift below: nil inherited
filament retract restart extra: nil inherited
filament retract speed: nil inherited
filament shrinkage compensation xy: 0 inherited
filament shrinkage compensation z: 0 inherited
filament soluble: 0 inherited
filament spool weight: 0 inherited
filament stamping distance: 0 inherited
filament stamping loading speed: 20 inherited
filament toolchange delay: 0 inherited
filament travel max lift: nil inherited
filament travel ramping lift: nil inherited
filament travel slope: nil inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
full fan speed layer: 0 inherited
idle temperature: 100 inherited
overhang fan speed 0: 0 inherited
overhang fan speed 1: 0 inherited
overhang fan speed 2: 0 inherited
overhang fan speed 3: 0 inherited
seal print: 1 inherited
smooth time: 0.03 inherited
start filament gcode: ; Filament gcode {if (enable_advance_pressure[0] == true)}M900 K[advance_pressure]{else}M900 K0{endif} T[smooth_time] inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "seal_print": [
    "1"
  ],
  "filament_id": [
    ""
  ],
  "smooth_time": [
    "0.03"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "filament_notes": [
    ""
  ],
  "hot_plate_temp": [
    "60"
  ],
  "box_temperature": [
    "0"
  ],
  "filament_colour": [
    "#3399FF"
  ],
  "filament_vendor": [
    "Overture"
  ],
  "advance_pressure": [
    "0.037"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "filament_density": [
    "1.2"
  ],
  "filament_soluble": [
    "0"
  ],
  "idle_temperature": [
    "100"
  ],
  "compatible_prints": [
    ""
  ],
  "enable_volume_fan": [
    "100"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament\n"
  ],
  "filament_load_time": [
    "0"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_flush_temp": [
    "240"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "enable_auxiliary_fan": [
    "100"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "overhang_fan_speed_0": [
    "0"
  ],
  "overhang_fan_speed_1": [
    "0"
  ],
  "overhang_fan_speed_2": [
    "0"
  ],
  "overhang_fan_speed_3": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "start_filament_gcode": [
    "; Filament gcode\n{if (enable_advance_pressure[0] == true)}M900 K[advance_pressure]{else}M900 K0{endif} T[smooth_time]\n"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "filament_spool_weight": [
    "0"
  ],
  "filament_travel_slope": [
    "nil"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_cooling_moves": [
    "0"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_retract_speed": [
    "nil"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "enable_advance_pressure": [
    "1"
  ],
  "filament_retract_length": [
    "nil"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_travel_max_lift": [
    "nil"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "enable_dynamic_fan_speeds": [
    "0"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_purge_multiplier": [
    "100"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_stamping_distance": [
    "0"
  ],
  "chamber_minimal_temperature": [
    "0"
  ],
  "compatible_prints_condition": [
    ""
  ],
  "enable_auxiliary_fan_unseal": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "filament_travel_ramping_lift": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "compatible_printers_condition": [
    "printer_model==\"X-Plus 4\" and nozzle_diameter[0]==0.4"
  ],
  "filament_max_volumetric_speed": [
    "11"
  ],
  "filament_retract_layer_change": [
    "nil"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_retract_before_travel": [
    "nil"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "filament_stamping_loading_speed": [
    "20"
  ],
  "nozzle_temperature_initial_layer": [
    "210"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_shrinkage_compensation_z": [
    "0"
  ],
  "filament_infill_max_crossing_speed": [
    "0"
  ],
  "filament_shrinkage_compensation_xy": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "disable_rapid_cooling_fan_first_layers": [
    "3"
  ],
  "name": "Overture PLA @X-Plus 4 0.4 nozzle",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:05