Fiberlogy Easy PET-G @0.6 nozzle MINI

Fiberlogy · PETG · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*PET*

→

Fiberlogy Easy PET-G

→

Fiberlogy Easy PET-G @0.6 nozzle MINI

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

*PETMINI06*

Settings

Basic information

Material variant: PETG inherited
Vendor: Fiberlogy inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 235 inherited
Nozzle (other layers) (°C): 235 inherited

Cooling

Fan minimum (%): 15 inherited
Fan maximum (%): 30 inherited
Disable fan for first N layers: 5 inherited
Full fan if layer below (sec): 15 inherited
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 15 via *PETMINI06*

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	80 inherited	80 inherited

Other settings

bridge fan speed: 60 inherited
compatible printers condition: printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6 via *PETMINI06*
cooling: 1 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #C0C0C0 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament deretract speed: 25 via *PETMINI06*
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: 1 via *PETMINI06*
filament retract length: nil via *PETMINI06*
filament retract lift: nil via *PETMINI06*
filament retract speed: 45 via *PETMINI06*
filament soluble: 0 inherited
filament spool weight: 330 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
full fan speed layer: 0 via *PETMINI06*
renamed from: Fiberlogy PETG @0.6 nozzle MINI overridden
was Fiberlogy PETG (inherited)
start filament gcode: M900 K{if nozzle_diameter[0]==0.6}0.12{elsif nozzle_diameter[0]==0.8}0.06{else}0.2{endif} ; Filament gcode {if printer_notes=~/.*PRINTER_MODEL_MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.22{elsif nozzle_diameter[0]==0.8}0.15{elsif nozzle_diameter[0]==0.4}0.4{elsif nozzle_diameter[0]==0.25}1.02{else}0{endif} {endif} via *PETMINI06*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#C0C0C0"
  ],
  "filament_vendor": [
    "Fiberlogy"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "M900 K{if nozzle_diameter[0]==0.6}0.12{elsif nozzle_diameter[0]==0.8}0.06{else}0.2{endif} ; Filament gcode\n\n{if printer_notes=~/.*PRINTER_MODEL_MINIIS.*/}\nM572 S{if nozzle_diameter[0]==0.6}0.22{elsif nozzle_diameter[0]==0.8}0.15{elsif nozzle_diameter[0]==0.4}0.4{elsif nozzle_diameter[0]==0.25}1.02{else}0{endif}\n{endif}"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "15"
  ],
  "filament_type": [
    "PETG"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "bridge_fan_speed": [
    "60"
  ],
  "nozzle_temperature": [
    "235"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "close_fan_the_first_x_layers": [
    "5"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "nozzle_temperature_initial_layer": [
    "235"
  ],
  "renamed_from": [
    "Fiberlogy PETG @0.6 nozzle MINI"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "filament_spool_weight": [
    "330"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "filament_retract_speed": [
    "45"
  ],
  "filament_retract_length": [
    "nil"
  ],
  "filament_deretract_speed": [
    "25"
  ],
  "filament_retract_before_travel": [
    "1"
  ],
  "name": "Fiberlogy Easy PET-G @0.6 nozzle MINI",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:03