Generic TPU @BBL H2S

Generic · TPU · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

Generic TPU @BBL H2S

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

fdm_filament_template_direct_dual

Compatible printers (3)

Bambu Lab H2S 0.4 nozzle
Bambu Lab H2S 0.6 nozzle
Bambu Lab H2S 0.8 nozzle

Settings

Basic information

Material variant: TPU inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 230 overridden
was 240 (inherited)
Nozzle (other layers) (°C): 230 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 3.2 overridden
was 3.2 (inherited)

Retraction

Retraction length (mm): nil overridden
was 0.4 (inherited)
Retraction speed (mm/s): nil via fdm_filament_template_direct_dual
Deretraction speed (mm/s): nil via fdm_filament_template_direct_dual

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	30 inherited	30 inherited
Engineering Plate	35 overridden was 30	35 overridden was 30
High Temp Plate	35 inherited	35 inherited

Other settings

additional cooling fan speed: 100 overridden
was 70 (inherited)
additional fan full speed layer: 0 inherited
close additional fan first x layers: 1 inherited
compatible printers: Bambu Lab H2S 0.4 nozzle, Bambu Lab H2S 0.6 nozzle, Bambu Lab H2S 0.8 nozzle overridden
was Bambu Lab X1 0.4 nozzle, Bambu Lab X1 0.6 nozzle, Bambu Lab X1 0.8 nozzle, Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab P1S 0.4 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1E 0.4 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle (inherited)
description: This filament is too soft and not compatible with the AMS. Printing it is of many requirements, and to get better printing quality, please refer to this wiki: TPU printing guide. inherited
filament adaptive volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament bridge speed: 25, 25 via fdm_filament_template_direct_dual
filament cooling before tower: 10, 10 overridden
filament enable overhang speed: 1, 1 via fdm_filament_template_direct_dual
filament extruder variant: Direct Drive Standard, Direct Drive High Flow via fdm_filament_template_direct_dual
filament flush temp: 0, 0 via fdm_filament_template_direct_dual
filament flush volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament id: GFU99 inherited
filament is support: 0 inherited
filament long retractions when cut: nil, nil via fdm_filament_template_direct_dual
filament minimal purge on wipe tower: 15 inherited
filament overhang 1 4 speed: 0, 0 via fdm_filament_template_direct_dual
filament overhang 2 4 speed: 50, 50 via fdm_filament_template_direct_dual
filament overhang 3 4 speed: 30, 30 via fdm_filament_template_direct_dual
filament overhang 4 4 speed: 10, 10 via fdm_filament_template_direct_dual
filament overhang totally speed: 10, 10 via fdm_filament_template_direct_dual
filament pre cooling temperature: 0, 0 via fdm_filament_template_direct_dual
filament pre cooling temperature nc: 0, 0 via fdm_filament_template_direct_dual
filament ramming travel time: 0, 0 overridden
filament ramming travel time nc: 0, 0 via fdm_filament_template_direct_dual
filament ramming volumetric speed: -1, -1 via fdm_filament_template_direct_dual
filament ramming volumetric speed nc: -1, -1 via fdm_filament_template_direct_dual
filament retract before wipe: nil, nil via fdm_filament_template_direct_dual
filament retract length nc: 14, 14 via fdm_filament_template_direct_dual
filament retract restart extra: nil, nil via fdm_filament_template_direct_dual
filament retract when changing layer: nil, nil via fdm_filament_template_direct_dual
filament retraction distances when cut: nil, nil via fdm_filament_template_direct_dual
filament retraction minimum travel: nil, nil via fdm_filament_template_direct_dual
filament soluble: 0 inherited
filament wipe: nil, nil via fdm_filament_template_direct_dual
filament wipe distance: nil, nil via fdm_filament_template_direct_dual
filament z hop: nil, nil via fdm_filament_template_direct_dual
filament z hop types: nil, nil via fdm_filament_template_direct_dual
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
long retractions when ec: 0, 0 overridden
nozzle temperature range high: 250 inherited
nozzle temperature range low: 200 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 95% inherited
override process overhang speed: 0, 0 via fdm_filament_template_direct_dual
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
retraction distances when ec: 0, 0 overridden
setting id: GFSU99_04 overridden
was GFSR99 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0 via fdm_filament_template_direct_dual

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "35"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "35"
  ],
  "cool_plate_temp": [
    "30"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "230",
    "230"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1",
    "1"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20",
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil",
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "35"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "35"
  ],
  "cool_plate_temp_initial_layer": [
    "30"
  ],
  "filament_max_volumetric_speed": [
    "3.2",
    "3.2"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "230",
    "230"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "100"
  ],
  "nozzle_temperature_range_low": [
    "200"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "description": "This filament is too soft and not compatible with the AMS. Printing it is of many requirements, and to get better printing quality, please refer to this wiki: TPU printing guide.",
  "filament_id": "GFU99",
  "setting_id": "GFSU99_04",
  "compatible_printers": [
    "Bambu Lab H2S 0.4 nozzle",
    "Bambu Lab H2S 0.6 nozzle",
    "Bambu Lab H2S 0.8 nozzle"
  ],
  "filament_flush_temp": [
    "0",
    "0"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil"
  ],
  "filament_bridge_speed": [
    "25",
    "25"
  ],
  "long_retractions_when_ec": [
    "0",
    "0"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "filament_retract_length_nc": [
    "14",
    "14"
  ],
  "filament_overhang_1_4_speed": [
    "0",
    "0"
  ],
  "filament_overhang_2_4_speed": [
    "50",
    "50"
  ],
  "filament_overhang_3_4_speed": [
    "30",
    "30"
  ],
  "filament_overhang_4_4_speed": [
    "10",
    "10"
  ],
  "retraction_distances_when_ec": [
    "0",
    "0"
  ],
  "filament_cooling_before_tower": [
    "10",
    "10"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_enable_overhang_speed": [
    "1",
    "1"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_overhang_totally_speed": [
    "10",
    "10"
  ],
  "filament_ramming_travel_time_nc": [
    "0",
    "0"
  ],
  "override_process_overhang_speed": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil"
  ],
  "filament_pre_cooling_temperature_nc": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed_nc": [
    "-1",
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0"
  ],
  "name": "Generic TPU @BBL H2S"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:17