Polymaker PolyDissolve S1 @PG

Polymaker · PVA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*PLA*

→

Polymaker PolyDissolve S1

→

Polymaker PolyDissolve S1 @PG

Includes (2)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Inherited from this (5)

Settings

Basic information

Material variant: PVA inherited
Vendor: Polymaker inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.13 inherited
Cost (/kg): 100 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 215 inherited
Chamber (°C): 20 inherited

Cooling

Fan minimum (%): 30 inherited
Fan maximum (%): 30 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 8 via *PLAPG*
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 4 overridden
was 4 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 inherited	55 inherited

Other settings

bridge fan speed: 40 inherited
chamber minimal temperature: 0 inherited
compatible printers condition: printer_model=~/(MK4|MK4IS|MK4ISMMU3|MK3.9|MK3.9MMU3)/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 and ! nozzle_high_flow[0] and ! single_extruder_multi_material overridden
was printer_notes=~/.*PRINTER_MODEL_VORON.*/ (inherited)
cooling: 1 inherited
cooling perimeter transition distance: 10 via *PLAPG*
cooling slowdown logic: consistent_surface via *PLAPG*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #F0EFB4 inherited
filament cooling final speed: 3.5 overridden
was 3.4 (inherited)
filament cooling initial speed: 10 overridden
was 2.2 (inherited)
filament cooling moves: 3 overridden
was 4 (inherited)
filament infill max crossing speed: 0 via *PLAPG*
filament infill max speed: 0 via *PLAPG*
filament load time: 10.5 overridden
was 0 (inherited)
filament loading speed: 10 overridden
was 28 (inherited)
filament loading speed start: 50 overridden
was 3 (inherited)
filament minimal purge on wipe tower: 35 overridden
was 35 (inherited)
filament purge multiplier: 81.25% via *PLAPG*
filament ramming parameters: 250 100 39.9677 40.1613 40.2581 40.1613 40.0645| 0.05 39.9548 0.45 40.1484 0.95 40.1484 1.45 40.1484 1.95 40.1484 2.45 40.1484 2.95 40.1484 3.45 40.1484 3.95 40.1484 4.45 40.1484 4.95 40.1484 overridden
was 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 (inherited)
filament soluble: 1 inherited
filament spool weight: 125 inherited
filament stamping distance: 45 overridden
filament stamping loading speed: 29 overridden
filament toolchange delay: 0 overridden
was 0 (inherited)
filament travel max lift: 0.6 via *PLAPG*
filament travel ramping lift: 1 via *PLAPG*
filament travel slope: 1 via *PLAPG*
filament unload time: 8.5 overridden
was 0 (inherited)
filament unloading speed: 60 overridden
was 90 (inherited)
filament unloading speed start: 60 overridden
was 100 (inherited)
full fan speed layer: 3 via *PLAPG*
idle temperature: 70 via *PLAPG*
start filament gcode: {if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/} M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.07{elsif nozzle_diameter[filament_extruder_id]==0.35}0.06{elsif nozzle_diameter[filament_extruder_id]==0.6}0.03{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.8}0.015{else}0{endif} ; Legacy LA {else} M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.036{elsif nozzle_diameter[filament_extruder_id]==0.5}0.025{elsif nozzle_diameter[filament_extruder_id]==0.6}0.022{elsif nozzle_diameter[filament_extruder_id]==0.8}0.014{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.08{else}0{endif} ; Pressure advance {endif} M142 S36 ; set heatbreak target temp via *PLAPG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "100"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#F0EFB4"
  ],
  "filament_vendor": [
    "Polymaker"
  ],
  "filament_density": [
    "1.13"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.07{elsif nozzle_diameter[filament_extruder_id]==0.35}0.06{elsif nozzle_diameter[filament_extruder_id]==0.6}0.03{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.8}0.015{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.036{elsif nozzle_diameter[filament_extruder_id]==0.5}0.025{elsif nozzle_diameter[filament_extruder_id]==0.6}0.022{elsif nozzle_diameter[filament_extruder_id]==0.8}0.014{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.08{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 39.9677 40.1613 40.2581 40.1613 40.0645| 0.05 39.9548 0.45 40.1484 0.95 40.1484 1.45 40.1484 1.95 40.1484 2.45 40.1484 2.95 40.1484 3.45 40.1484 3.95 40.1484 4.45 40.1484 4.95 40.1484"
  ],
  "filament_cooling_final_speed": [
    "3.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_model=~/(MK4|MK4IS|MK4ISMMU3|MK3.9|MK3.9MMU3)/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 and ! nozzle_high_flow[0] and ! single_extruder_multi_material"
  ],
  "filament_max_volumetric_speed": [
    "4"
  ],
  "filament_cooling_initial_speed": [
    "10"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_type": [
    "PVA"
  ],
  "hot_plate_temp": [
    "55"
  ],
  "bridge_fan_speed": [
    "40"
  ],
  "nozzle_temperature": [
    "215"
  ],
  "chamber_temperature": [
    "20"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "chamber_minimal_temperature": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_spool_weight": [
    "125"
  ],
  "idle_temperature": [
    "70"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "0.6"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_purge_multiplier": [
    "81.25%"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_stamping_loading_speed": [
    "29"
  ],
  "filament_infill_max_crossing_speed": [
    "0"
  ],
  "name": "Polymaker PolyDissolve S1 @PG",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:03