Verbatim BVOH @MK4S 0.6

Verbatim · PVA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

Verbatim BVOH

→

Verbatim BVOH @PG

→

Verbatim BVOH @PG 0.6

→

Verbatim BVOH @MK4S 0.6

Includes (7)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Inherited from this (1)

Fiberlogy BVOH @MK4S 0.6

Settings

Basic information

Material variant: PVA inherited
Vendor: Verbatim inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.14 inherited
Cost (/kg): 159.98 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 220 inherited

Cooling

Fan minimum (%): 10 via *ABS06PG4S*
Fan maximum (%): 10 via *ABS06PG4S*
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 5 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 inherited	60 inherited

Other settings

bridge fan speed: 75 overridden
was 100 (inherited)
compatible printers condition: printer_model=~/(MK4S|MK4SMMU3|MK3.9S|MK3.9SMMU3)/ and nozzle_diameter[0]==0.6 and ! nozzle_high_flow[0] overridden
was printer_model=~/(MK4|MK4IS|MK4ISMMU3|MK3.9|MK3.9MMU3)/ and nozzle_diameter[0]==0.6 and ! nozzle_high_flow[0] (inherited)
cooling: 0 inherited
cooling perimeter transition distance: 10 via *ABS06PG*
cooling slowdown logic: consistent_surface via *ABS06PG*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament colour: #FFFFD7 inherited
filament cooling final speed: 3.5 overridden
was 3.5 (inherited)
filament cooling initial speed: 10 overridden
was 10 (inherited)
filament cooling moves: 3 overridden
was 3 (inherited)
filament infill max crossing speed: 0 via *ABS06PG*
filament infill max speed: 0 via *ABS06PG*
filament load time: 10.5 overridden
was 10.5 (inherited)
filament loading speed: 10 overridden
was 10 (inherited)
filament loading speed start: 50 overridden
was 50 (inherited)
filament minimal purge on wipe tower: 35 overridden
was 35 (inherited)
filament purge multiplier: 200% inherited
filament ramming parameters: 250 100 39.9677 40.1613 40.2581 40.1613 40.0645| 0.05 39.9548 0.45 40.1484 0.95 40.1484 1.45 40.1484 1.95 40.1484 2.45 40.1484 2.95 40.1484 3.45 40.1484 3.95 40.1484 4.45 40.1484 4.95 40.1484 overridden
was 250 100 39.9677 40.1613 40.2581 40.1613 40.0645| 0.05 39.9548 0.45 40.1484 0.95 40.1484 1.45 40.1484 1.95 40.1484 2.45 40.1484 2.95 40.1484 3.45 40.1484 3.95 40.1484 4.45 40.1484 4.95 40.1484 (inherited)
filament soluble: 1 inherited
filament spool weight: 235 inherited
filament stamping distance: 45 overridden
was 45 (inherited)
filament stamping loading speed: 29 overridden
was 29 (inherited)
filament toolchange delay: 0 overridden
was 0 (inherited)
filament unload time: 8.5 overridden
was 8.5 (inherited)
filament unloading speed: 60 overridden
was 60 (inherited)
filament unloading speed start: 60 overridden
was 60 (inherited)
idle temperature: 100 via *ABS06PG*
start filament gcode: {if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/} M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.04{elsif nozzle_diameter[filament_extruder_id]==0.25}0.1{elsif nozzle_diameter[filament_extruder_id]==0.3}0.06{elsif nozzle_diameter[filament_extruder_id]==0.35}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.03{elsif nozzle_diameter[filament_extruder_id]==0.6}0.02{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{else}0{endif} ; Legacy LA {else} M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.012{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Pressure advance {endif} M142 S40 ; set heatbreak target temp via *ABS06PG*

Raw resolved JSON

{
  "cooling": [
    "0"
  ],
  "filament_cost": [
    "159.98"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#FFFFD7"
  ],
  "filament_vendor": [
    "Verbatim"
  ],
  "filament_density": [
    "1.14"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.04{elsif nozzle_diameter[filament_extruder_id]==0.25}0.1{elsif nozzle_diameter[filament_extruder_id]==0.3}0.06{elsif nozzle_diameter[filament_extruder_id]==0.35}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.03{elsif nozzle_diameter[filament_extruder_id]==0.6}0.02{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.012{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S40 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 39.9677 40.1613 40.2581 40.1613 40.0645| 0.05 39.9548 0.45 40.1484 0.95 40.1484 1.45 40.1484 1.95 40.1484 2.45 40.1484 2.95 40.1484 3.45 40.1484 3.95 40.1484 4.45 40.1484 4.95 40.1484"
  ],
  "filament_cooling_final_speed": [
    "3.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_model=~/(MK4S|MK4SMMU3|MK3.9S|MK3.9SMMU3)/ and nozzle_diameter[0]==0.6 and ! nozzle_high_flow[0]"
  ],
  "filament_max_volumetric_speed": [
    "5"
  ],
  "filament_cooling_initial_speed": [
    "10"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "10"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_type": [
    "PVA"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "bridge_fan_speed": [
    "75"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "filament_spool_weight": [
    "235"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "idle_temperature": [
    "100"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_stamping_loading_speed": [
    "29"
  ],
  "filament_infill_max_crossing_speed": [
    "0"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_purge_multiplier": [
    "200%"
  ],
  "name": "Verbatim BVOH @MK4S 0.6",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:03