Filament PM PLA+ @HF0.4

Filament PM · PLA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

Filament PM PLA+ @HF0.4

Includes (4)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Inherited from this (3)

Settings

Basic information

Material variant: PLA via *PLAHF*
Vendor: Generic via *PLAHF*
Diameter (mm): 1.75 via *PLAHF*
Density (g/cm³): 1.24 via *PLAHF*
Cost (/kg): 0 via *PLAHF*

Print temperature

Nozzle (initial layer) (°C): 230 via *PLA225*
Nozzle (other layers) (°C): 225 via *PLA225*
Chamber (°C): 20 via *PLAHF*

Cooling

Fan minimum (%): 100 via *PLAHF*
Fan maximum (%): 100 via *PLAHF*
Disable fan for first N layers: 1 via *PLAHF*
Full fan if layer below (sec): 100 via *PLAHF*
Slow down if layer below (sec): 12 via *PLAHF*
Min speed when slowed (mm/s): 15 via *PLAHF*

Flow

Flow ratio: 1 via *PLAHF*
Max volumetric speed (mm³/s): 21 via *PLAHF*

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 via include	55 via include

Other settings

bridge fan speed: 100 via *PLAHF*
chamber minimal temperature: 0 via *PLAHF*
compatible printers condition: printer_notes=~/.*PRINTER_MODEL_VORON.*/ via *PLAHF*
cooling: 1 via *PLAHF*
cooling perimeter transition distance: 10 via *PLAHF*
cooling slowdown logic: consistent_surface via *PLAHF*
end filament gcode: ; Filament-specific end gcode via *PLAHF*
fan always on: 1 via *PLAHF*
filament colour: #FF3232 via *PLAHF*
filament cooling final speed: 3.4 via *PLAHF*
filament cooling initial speed: 2.2 via *PLAHF*
filament cooling moves: 4 via *PLAHF*
filament infill max crossing speed: 0 via *PLAPG*
filament infill max speed: 0 via *PLAPG*
filament load time: 0 via *PLAHF*
filament loading speed: 28 via *PLAHF*
filament loading speed start: 3 via *PLAHF*
filament minimal purge on wipe tower: 15 via *PLAHF*
filament purge multiplier: 81.25% via *PLAPG*
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 via *PLAHF*
filament soluble: 0 via *PLAHF*
filament spool weight: 0 inherited
filament stamping distance: 45 via *PLAPG*
filament stamping loading speed: 29 via *PLAPG*
filament toolchange delay: 0 via *PLAHF*
filament travel max lift: 0.6 via *PLAPG*
filament travel ramping lift: 1 via *PLAPG*
filament travel slope: 1 via *PLAPG*
filament unload time: 0 via *PLAHF*
filament unloading speed: 90 via *PLAHF*
filament unloading speed start: 100 via *PLAHF*
full fan speed layer: 4 via *PLAHF*
idle temperature: 70 via *PLAPG*
start filament gcode: ; Filament-specific start gcode via *PLAHF*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#FF3232"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "start_filament_gcode": [
    "; Filament-specific start gcode"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_MODEL_VORON.*/"
  ],
  "filament_max_volumetric_speed": [
    "21"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_type": [
    "PLA"
  ],
  "hot_plate_temp": [
    "55"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "225"
  ],
  "chamber_temperature": [
    "20"
  ],
  "full_fan_speed_layer": [
    "4"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "chamber_minimal_temperature": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_spool_weight": [
    "0"
  ],
  "idle_temperature": [
    "70"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "0.6"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_purge_multiplier": [
    "81.25%"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_stamping_loading_speed": [
    "29"
  ],
  "filament_infill_max_crossing_speed": [
    "0"
  ],
  "name": "Filament PM PLA+ @HF0.4",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:55