slicershare (test)
← Fiberlogy ASA @XL 0.8

History of Fiberlogy ASA @XL 0.8

Direct edits to this profile, and edits to any profile it inherits from. An inherited change can shift this profile's effective behavior even when this profile itself wasn't touched.

Inherits from: *common* → *ABS* → Fiberlogy ASA → Fiberlogy ASA @XL
  1. direct edit v1 — created
    2026-05-19 11:52
    Profile created at this point. No prior version to diff against.
  2. via parent v1 of Fiberlogy ASA @XL — created
    2026-05-19 11:52
    Profile created at this point. No prior version to diff against.
  3. via parent v40 of *common* — updated
    2026-05-19 11:15
    Settings (19)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_ULTIMAKER.*/ → —
    • cooling 0 → 1
    • end filament gcode added —
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament diameter 2.85 → 1.75
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • slow down layer time 6 → 20
    • slow down min speed 5 → 15
    • start filament gcode added —
  4. via parent v27 of *ABS* — updated
    2026-05-19 11:15
    Settings (22)
    • bridge fan speed added 10
    • close fan the first x layers added 3
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_E2D.*/ → printer_notes=~/.*PRINTER_VENDOR_ULTIMAKER.*/
    • cooling 0 → 1
    • fan always on 0 → 1
    • fan cooling layer time added 15
    • fan max speed added 5
    • fan min speed added 5
    • filament colour added #C0C0C0
    • filament cost added 0
    • filament density added 1.10
    • filament diameter 1.75 → 2.85
    • filament flow ratio added 1
    • filament max volumetric speed added 0
    • filament notes added —
    • filament soluble added 0
    • hot plate temp 90 → 80
    • hot plate temp initial layer 90 → 80
    • nozzle temperature 240 → 235
    • nozzle temperature initial layer 230 → 240
    • slow down layer time added 15
    • slow down min speed 60 → 10
  5. via parent v39 of *common* — updated
    2026-05-19 11:15
    Settings (10)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_E2D.*/ → printer_notes=~/.*PRINTER_VENDOR_ULTIMAKER.*/
    • cooling added 0
    • filament cost added 0
    • filament density added 0
    • filament diameter 1.75 → 2.85
    • filament flow ratio added 1
    • filament notes added —
    • filament soluble added 0
    • slow down layer time added 6
    • slow down min speed added 5
  6. via parent v26 of *ABS* — updated
    2026-05-19 11:15
    Settings (33)
    • bridge fan speed removed 25
    • close fan the first x layers removed 3
    • compatible printers condition printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) → printer_notes=~/.*PRINTER_VENDOR_E2D.*/
    • end filament gcode removed ; Filament-specific end gcode
    • fan cooling layer time removed 20
    • fan max speed removed 30
    • fan min speed removed 20
    • filament colour removed #FFF2EC
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost removed 0
    • filament density removed 0
    • filament flow ratio removed 1
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed removed 11
    • filament minimal purge on wipe tower removed 15
    • filament notes removed —
    • filament ramming parameters removed 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament soluble removed 0
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • hot plate temp 110 → 90
    • hot plate temp initial layer 100 → 90
    • nozzle temperature 255 → 240
    • nozzle temperature initial layer 255 → 230
    • slow down layer time removed 15
    • slow down min speed 15 → 60
    • start filament gcode removed {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode {endif}
  7. via parent v38 of *common* — updated
    2026-05-19 11:15
    Settings (23)
    • compatible printers condition ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) and printer_notes!~/.*PG.*/ → printer_notes=~/.*PRINTER_VENDOR_E2D.*/
    • cooling removed 1
    • end filament gcode removed ; Filament-specific end gcode
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost removed 0
    • filament density removed 0
    • filament flow ratio removed 1
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament minimal purge on wipe tower removed 15
    • filament notes removed —
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament soluble removed 0
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • slow down layer time removed 15
    • slow down min speed removed 15
    • start filament gcode removed M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif} ; Filament gcode
  8. via parent v2 of Fiberlogy ASA — updated
    2026-05-19 11:13
    Settings (12)
    • compatible printers condition printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1) → printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
    • filament cooling final speed 2 → 3.4
    • filament cooling initial speed 3 → 2.2
    • filament cooling moves 1 → 4
    • filament loading speed 14 → 28
    • filament loading speed start 19 → 3
    • filament max volumetric speed 0 → 11
    • filament minimal purge on wipe tower 0 → 15
    • filament unloading speed 20 → 90
    • hot plate temp 100 → 110
    • hot plate temp initial layer 100 → 105
    • start filament gcode — → {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode {endif}
  9. via parent v25 of *ABS* — updated
    2026-05-19 11:08
    Settings (31)
    • bridge fan speed 15 → 25
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_HSP.*/ → printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
    • cooling 1 → 0
    • end filament gcode added ; Filament-specific end gcode
    • fan always on 1 → 0
    • fan max speed 15 → 30
    • fan min speed 15 → 20
    • filament colour #3A80CA → #FFF2EC
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 20 → 0
    • filament density 1.04 → 0
    • filament flow ratio 0.92 → 1
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed 15 → 11
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • full fan speed layers removed 7
    • hot plate temp 100 → 110
    • idle temperature removed 170
    • nozzle temperature 250 → 255
    • nozzle temperature initial layer 245 → 255
    • slow down layer time 10 → 15
    • start filament gcode added {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode {endif}
  10. via parent v37 of *common* — updated
    2026-05-19 11:08
    Settings (18)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_HSP.*/ → ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) and printer_notes!~/.*PG.*/
    • cooling 0 → 1
    • end filament gcode added ; Filament-specific end gcode
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament flow ratio added 1
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • slow down layer time 10 → 15
    • start filament gcode added M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif} ; Filament gcode
  11. via parent v24 of *ABS* — updated
    2026-05-19 11:08
    Settings (30)
    • bridge fan speed 25 → 15
    • compatible printers condition printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1) → printer_notes=~/.*PRINTER_VENDOR_HSP.*/
    • cooling 0 → 1
    • end filament gcode removed ; Filament-specific end gcode
    • fan always on 0 → 1
    • fan max speed 30 → 15
    • fan min speed 20 → 15
    • filament colour #FFF2EC → #3A80CA
    • filament cooling final speed removed 2
    • filament cooling initial speed removed 3
    • filament cooling moves removed 1
    • filament cost 0 → 20
    • filament density 0 → 1.04
    • filament flow ratio 1 → 0.92
    • filament load time removed 0
    • filament loading speed removed 14
    • filament loading speed start removed 19
    • filament max volumetric speed 0 → 15
    • filament minimal purge on wipe tower removed 0
    • filament ramming parameters removed 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 20
    • filament unloading speed start removed 100
    • full fan speed layers added 7
    • idle temperature added 170
    • nozzle temperature 255 → 250
    • nozzle temperature initial layer 255 → 245
    • slow down min speed 10 → 15
    • start filament gcode removed —
  12. via parent v36 of *common* — updated
    2026-05-19 11:08
    Settings (18)
    • compatible printers condition printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1) → printer_notes=~/.*PRINTER_VENDOR_HSP.*/
    • cooling 1 → 0
    • end filament gcode removed ; Filament-specific end gcode
    • filament cooling final speed removed 2
    • filament cooling initial speed removed 3
    • filament cooling moves removed 1
    • filament flow ratio removed 1
    • filament load time removed 0
    • filament loading speed removed 14
    • filament loading speed start removed 19
    • filament minimal purge on wipe tower removed 0
    • filament ramming parameters removed 130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 20
    • filament unloading speed start removed 100
    • slow down min speed 10 → 15
    • start filament gcode removed —
  13. via parent v1 of Fiberlogy ASA — created
    2026-05-19 11:07
    Profile created at this point. No prior version to diff against.
  14. via parent v23 of *ABS* — updated
    2026-05-19 11:06
    Settings (24)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_BIBO.*/ → printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
    • end filament gcode added ; Filament-specific end gcode
    • fan max speed 0 → 30
    • fan min speed 0 → 20
    • filament cooling final speed added 2
    • filament cooling initial speed added 3
    • filament cooling moves added 1
    • filament cost 20 → 0
    • filament density 1.04 → 0
    • filament load time added 0
    • filament loading speed added 14
    • filament loading speed start added 19
    • filament max volumetric speed 11 → 0
    • filament minimal purge on wipe tower 15 → 0
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 20
    • filament unloading speed start added 100
    • nozzle temperature 245 → 255
    • nozzle temperature initial layer 245 → 255
    • slow down layer time 20 → 10
    • slow down min speed 15 → 10
    • start filament gcode added —
    • top fan speed removed 0
  15. via parent v35 of *common* — updated
    2026-05-19 11:06
    Settings (18)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_BIBO.*/ → printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
    • cooling 0 → 1
    • end filament gcode added ; Filament-specific end gcode
    • filament cooling final speed added 2
    • filament cooling initial speed added 3
    • filament cooling moves added 1
    • filament load time added 0
    • filament loading speed added 14
    • filament loading speed start added 19
    • filament minimal purge on wipe tower 15 → 0
    • filament ramming parameters 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 → 130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 20
    • filament unloading speed start added 100
    • slow down layer time 20 → 10
    • slow down min speed 15 → 10
    • start filament gcode added —
  16. via parent v22 of *ABS* — updated
    2026-05-19 11:06
    Settings (5)
    • bridge fan speed 30 → 25
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_ELEGOO.*/ → printer_notes=~/.*PRINTER_VENDOR_BIBO.*/
    • filament colour #DDDDDD → #FFF2EC
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
  17. via parent v34 of *common* — updated
    2026-05-19 11:06
    Settings (3)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_ELEGOO.*/ → printer_notes=~/.*PRINTER_VENDOR_BIBO.*/
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
  18. via parent v21 of *ABS* — updated
    2026-05-19 11:06
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (5)
    • compatible printers added —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/ → printer_notes=~/.*PRINTER_VENDOR_ELEGOO.*/
    • filament max volumetric speed 0 → 11
    • filament minimal purge on wipe tower removed 90
    • filament vendor removed Generic
  19. via parent v33 of *common* — updated
    2026-05-19 11:06
    Settings (2)
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_ELEGOO.*/
    • slow down layer time 0 → 20
  20. via parent v32 of *common* — updated
    2026-05-19 11:05
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (5)
    • compatible printers added —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • filament minimal purge on wipe tower removed 90
    • filament vendor removed Generic
    • slow down layer time 20 → 0
  21. via parent v20 of *ABS* — updated
    2026-05-19 11:05
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (34)
    • bridge fan speed added 30
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_RIGID3D.*/ and printer_notes=~/.*PRINTER_HAS_HEATEDBED.*/ → printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • cooling 1 → 0
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time 60 → 20
    • filament colour added #DDDDDD
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 0 → 20
    • filament density added 1.04
    • filament deretract speed removed nil
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower 15 → 90
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament spool weight removed 0
    • filament vendor added Generic
    • filament wipe removed nil
    • hot plate temp added 100
    • hot plate temp initial layer added 100
    • nozzle temperature added 245
    • nozzle temperature initial layer added 245
    • slow down layer time 10 → 20
    • slow down min speed 10 → 15
    • start filament gcode removed ; Filament gcode
    • top fan speed added 0
  22. via parent v31 of *common* — updated
    2026-05-19 11:05
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (26)
    • close fan the first x layers removed 3
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • cooling added 0
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time removed 60
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament density added 0
    • filament deretract speed removed nil
    • filament minimal purge on wipe tower 15 → 90
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament spool weight removed 0
    • filament vendor added Generic
    • filament wipe removed nil
    • slow down layer time 10 → 20
    • slow down min speed 10 → 15
    • start filament gcode removed ; Filament gcode
  23. via parent v19 of *ABS* — updated
    2026-05-19 11:05
    Settings (33)
    • bridge fan speed removed 30
    • close fan the first x layers 2 → 3
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/ → printer_notes=~/.*PRINTER_VENDOR_RIGID3D.*/ and printer_notes=~/.*PRINTER_HAS_HEATEDBED.*/
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time 20 → 60
    • filament colour removed #DDDDDD
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 20 → 0
    • filament density removed 1.04
    • filament deretract speed added nil
    • filament minimal purge on wipe tower added 15
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament wipe added nil
    • hot plate temp removed 90
    • hot plate temp initial layer removed 90
    • nozzle temperature removed 255
    • nozzle temperature initial layer removed 255
    • slow down layer time 8 → 10
    • slow down min speed 30 → 10
    • start filament gcode added ; Filament gcode
    • top fan speed removed 0
  24. via parent v30 of *common* — updated
    2026-05-19 11:05
    Settings (26)
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • cooling removed 1
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time added 60
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament density removed 0
    • filament deretract speed added nil
    • filament minimal purge on wipe tower added 15
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament wipe added nil
    • slow down layer time 8 → 10
    • slow down min speed 30 → 10
    • start filament gcode added ; Filament gcode
  25. via parent v18 of *ABS* — updated
    2026-05-19 11:05
    Settings (9)
    • close fan the first x layers 3 → 2
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_Artillery.*/ → printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • cooling 0 → 1
    • filament colour #6603FC → #DDDDDD
    • filament max volumetric speed removed 11
    • nozzle temperature 240 → 255
    • nozzle temperature initial layer 240 → 255
    • slow down layer time 15 → 8
    • slow down min speed 15 → 30
  26. via parent v29 of *common* — updated
    2026-05-19 11:05
    Settings (3)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_Artillery.*/ → printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • slow down layer time 15 → 8
    • slow down min speed 15 → 30
  27. via parent v17 of *ABS* — updated
    2026-05-19 11:05
    Settings (8)
    • close fan the first x layers 0 → 3
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Artillery.*/
    • filament colour #DDDDDD → #6603FC
    • hot plate temp 100 → 90
    • hot plate temp initial layer 110 → 90
    • nozzle temperature 245 → 240
    • nozzle temperature initial layer 250 → 240
    • slow down layer time 20 → 15
  28. via parent v28 of *common* — updated
    2026-05-19 11:05
    Settings (4)
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Artillery.*/
    • cooling 0 → 1
    • filament flow ratio 0.9 → 1
    • slow down layer time 20 → 15
  29. via parent v16 of *ABS* — updated
    2026-05-19 11:05
    Settings (4)
    • close fan the first x layers 3 → 0
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • hot plate temp initial layer 100 → 110
    • nozzle temperature initial layer 245 → 250
  30. via parent v27 of *common* — updated
    2026-05-19 11:05
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (15)
    • bridge fan speed removed 100
    • close fan the first x layers removed 3
    • compatible printers added —
    • cooling 1 → 0
    • fan always on removed 0
    • fan cooling layer time removed 10
    • filament colour removed #29B2B2
    • filament cost added 0
    • filament density added 0
    • filament flow ratio 1 → 0.9
    • filament notes added —
    • filament vendor removed Generic
    • full fan speed layer removed 0
    • slow down layer time 5 → 20
    • slow down min speed 10 → 15
  31. via parent v26 of *common* — updated
    2026-05-19 11:04
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (15)
    • bridge fan speed added 100
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • cooling 0 → 1
    • fan always on added 0
    • fan cooling layer time added 10
    • filament colour added #29B2B2
    • filament cost removed 0
    • filament density removed 0
    • filament notes removed —
    • filament vendor added Generic
    • full fan speed layer added 0
    • slow down layer time 20 → 5
    • slow down min speed 15 → 10
  32. via parent v15 of *ABS* — updated
    2026-05-19 11:04
    Settings (17)
    • bridge fan speed 50 → 30
    • compatible printers added —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/ → printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • fan cooling layer time 15 → 20
    • fan max speed 50 → 0
    • fan min speed 20 → 0
    • filament colour #FF8000 → #DDDDDD
    • filament cost 30 → 20
    • filament density 1.27 → 1.04
    • filament max volumetric speed 8 → 11
    • filament soluble added 0
    • hot plate temp 70 → 100
    • hot plate temp initial layer 80 → 100
    • nozzle temperature 235 → 245
    • nozzle temperature initial layer 235 → 245
    • slow down layer time 10 → 20
    • top fan speed added 0
  33. via parent v25 of *common* — updated
    2026-05-19 11:04
    Settings (6)
    • compatible printers added —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/ → printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • filament cost added 0
    • filament density added 0
    • filament soluble added 0
    • slow down layer time 10 → 20
  34. via parent v14 of *ABS* — updated
    2026-05-19 11:04
    Settings (18)
    • bridge fan speed 30 → 50
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ → printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/
    • fan cooling layer time 20 → 15
    • fan max speed 0 → 50
    • fan min speed 0 → 20
    • filament colour #DDDDDD → #FF8000
    • filament cost 20 → 30
    • filament density 1.04 → 1.27
    • filament max volumetric speed 11 → 8
    • filament soluble removed 0
    • hot plate temp 100 → 70
    • hot plate temp initial layer 100 → 80
    • idle temperature removed 180
    • nozzle temperature 245 → 235
    • nozzle temperature initial layer 245 → 235
    • slow down layer time 20 → 10
    • top fan speed removed 0
  35. via parent v24 of *common* — updated
    2026-05-19 11:04
    Settings (6)
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ → printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/
    • filament cost removed 0
    • filament density removed 0
    • filament soluble removed 0
    • slow down layer time 20 → 10
  36. via parent v13 of *ABS* — updated
    2026-05-19 11:04
    Settings (24)
    • bridge fan speed 25 → 30
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/ → printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
    • fan max speed 30 → 0
    • fan min speed 20 → 0
    • filament colour #FFF2EC → #DDDDDD
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 0 → 20
    • filament density 0 → 1.04
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • idle temperature added 180
    • nozzle temperature 255 → 245
    • nozzle temperature initial layer 255 → 245
    • slow down layer time 15 → 20
    • top fan speed added 0
  37. via parent v23 of *common* — updated
    2026-05-19 11:04
    Settings (15)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/ → printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
    • cooling 1 → 0
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • slow down layer time 15 → 20
  38. via parent v12 of *ABS* — updated
    2026-05-19 11:03
    Settings (30)
    • bridge fan speed 30 → 25
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan max speed 0 → 30
    • fan min speed 0 → 20
    • filament colour #DDDDDD → #FFF2EC
    • filament cost 20 → 0
    • filament density 1.04 → 0
    • filament deretract speed removed nil
    • filament ramming parameters 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 → 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament spool weight removed 0
    • filament wipe removed nil
    • full fan speed layer removed 0
    • nozzle temperature 245 → 255
    • nozzle temperature initial layer 245 → 255
    • slow down layer time 5 → 15
    • slow down min speed 10 → 15
    • start filament gcode removed ; Filament gcode
    • top fan speed removed 0
  39. via parent v22 of *common* — updated
    2026-05-19 11:03
    Identity / metadata
    • Vendor: QIDI → Unknown
    • Material: PLA → OTHER
    Settings (70)
    • bridge fan speed removed 100
    • chamber temperature removed 0
    • close fan the first x layers removed 1
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • cooling perimeter transition distance removed 3
    • cooling slowdown logic removed consistent_surface
    • disable rapid cooling fan first layers removed 3
    • enable advance pressure removed 1
    • enable auxiliary fan removed 100
    • enable auxiliary fan unseal removed 0
    • enable dynamic fan speeds removed 0
    • enable volume fan removed 100
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan always on removed 1
    • fan cooling layer time removed 60
    • fan max speed removed 100
    • fan min speed removed 100
    • filament colour removed #3399FF
    • filament cooling final speed 0 → 3.4
    • filament cooling initial speed 0 → 2.2
    • filament cooling moves 0 → 4
    • filament density 1.24 → 0
    • filament deretract speed removed nil
    • filament flow ratio 0.98 → 1
    • filament loading speed 0 → 28
    • filament loading speed start 0 → 3
    • filament max volumetric speed removed 20
    • filament minimal purge on wipe tower 5 → 15
    • filament multitool ramming removed 0
    • filament multitool ramming flow removed 10
    • filament multitool ramming volume removed 10
    • filament purge multiplier removed 100
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament shrink removed 100
    • filament spool weight removed 0
    • filament stamping distance removed 0
    • filament stamping loading speed removed 0
    • filament travel max lift removed nil
    • filament travel ramping lift removed nil
    • filament travel slope removed nil
    • filament type removed PLA
    • filament unloading speed 0 → 90
    • filament unloading speed start 0 → 100
    • filament vendor removed QIDI
    • filament wipe removed nil
    • filament wipe distance removed nil
    • full fan speed layer removed 0
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • idle temperature removed 100
    • nozzle temperature removed 220
    • nozzle temperature initial layer removed 210
    • overhang fan speed 0 removed 0
    • overhang fan speed 1 removed 0
    • overhang fan speed 2 removed 0
    • overhang fan speed 3 removed 0
    • seal print removed 1
    • slow down layer time 8 → 15
    • slow down min speed 20 → 15
    • start filament gcode removed ; Filament gcode M900 K0.02 T0.03
  40. via parent v21 of *common* — updated
    2026-05-19 11:01
    Identity / metadata
    • Vendor: Cocoa Press → QIDI
    • Material: OTHER → PLA
    Settings (54)
    • bridge fan speed 0 → 100
    • chamber temperature added 0
    • close fan the first x layers 3 → 1
    • compatible printers added —
    • compatible printers condition added —
    • compatible prints added —
    • compatible prints condition added —
    • cooling 0 → 1
    • cooling perimeter transition distance added 3
    • cooling slowdown logic added consistent_surface
    • disable rapid cooling fan first layers added 3
    • enable advance pressure added 1
    • enable auxiliary fan added 100
    • enable auxiliary fan unseal added 0
    • enable volume fan added 100
    • fan always on 0 → 1
    • fan min speed 35 → 100
    • filament colour #3D2113 → #3399FF
    • filament cooling final speed 3.4 → 0
    • filament cooling initial speed 2.2 → 0
    • filament cooling moves 4 → 0
    • filament cost 70 → 0
    • filament density 1.2912 → 1.24
    • filament diameter 22.66 → 1.75
    • filament flow ratio 1 → 0.98
    • filament loading speed 28 → 0
    • filament loading speed start 3 → 0
    • filament max volumetric speed 0 → 20
    • filament minimal purge on wipe tower 15 → 5
    • filament multitool ramming added 0
    • filament multitool ramming flow added 10
    • filament multitool ramming volume added 10
    • filament purge multiplier added 100
    • filament shrink added 100
    • filament stamping distance added 0
    • filament stamping loading speed added 0
    • filament travel max lift added nil
    • filament travel ramping lift added nil
    • filament travel slope added nil
    • filament type added PLA
    • filament unloading speed 90 → 0
    • filament unloading speed start 100 → 0
    • filament vendor Cocoa Press → QIDI
    • filament wipe 1 → nil
    • filament wipe distance added nil
    • hot plate temp 0 → 60
    • hot plate temp initial layer 0 → 60
    • idle temperature nil → 100
    • nozzle temperature added 220
    • nozzle temperature initial layer 0 → 210
    • seal print added 1
    • slow down layer time 5 → 8
    • slow down min speed 10 → 20
    • start filament gcode ; Filament gcode → ; Filament gcode M900 K0.02 T0.03
  41. via parent v20 of *common* — updated
    2026-05-19 11:01
    Identity / metadata
    • Vendor: Unknown → Cocoa Press
    Settings (55)
    • bridge fan speed added 0
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/
    • cooling 0,0 → 0
    • enable dynamic fan speeds added 0
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan always on added 0
    • fan cooling layer time added 60
    • fan max speed added 100
    • fan min speed added 35
    • filament colour added #3D2113
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 0,0 → 70
    • filament density 0,0 → 1.2912
    • filament deretract speed added nil
    • filament diameter 1.75,1.75 → 22.66
    • filament flow ratio 1,1 → 1
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament soluble 0,0 → 0
    • filament spool weight added 0
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • filament vendor added Cocoa Press
    • filament wipe added 1
    • full fan speed layer added 0
    • hot plate temp added 0
    • hot plate temp initial layer added 0
    • idle temperature added nil
    • nozzle temperature initial layer added 0
    • overhang fan speed 0 added 0
    • overhang fan speed 1 added 0
    • overhang fan speed 2 added 0
    • overhang fan speed 3 added 0
    • slow down layer time 20,20 → 5
    • slow down min speed 15,15 → 10
    • start filament gcode added ; Filament gcode
  42. via parent v19 of *common* — updated
    2026-05-19 11:01
    Identity / metadata
    • Material: PLA → OTHER
    Settings (49)
    • bridge fan speed removed 100
    • close fan the first x layers removed 1
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • cooling 1 → 0,0
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan always on removed 0
    • fan cooling layer time removed 600
    • fan max speed removed 100
    • fan min speed removed 100
    • filament colour removed #29B2B2
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 24 → 0,0
    • filament density 0 → 0,0
    • filament deretract speed removed nil
    • filament diameter 1.75 → 1.75,1.75
    • filament flow ratio 0.92 → 1,1
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed removed 0
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament soluble 0 → 0,0
    • filament toolchange delay removed 0
    • filament type removed PLA
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • filament wipe removed nil
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • nozzle temperature removed 190
    • nozzle temperature initial layer removed 190
    • slow down layer time 1 → 20,20
    • slow down min speed 30 → 15,15
    • start filament gcode removed ; Filament gcode
  43. via parent v18 of *common* — updated
    2026-05-19 11:00
    Settings (12)
    • close fan the first x layers 2 → 1
    • fan always on 1 → 0
    • fan cooling layer time 60 → 600
    • fan min speed 35 → 100
    • filament cost 0 → 24
    • filament flow ratio 1 → 0.92
    • filament spool weight removed 0
    • full fan speed layer removed 0
    • nozzle temperature 210 → 190
    • nozzle temperature initial layer 210 → 190
    • slow down layer time 5 → 1
    • slow down min speed 10 → 30
  44. via parent v11 of *ABS* — updated
    2026-05-19 11:00
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (35)
    • compatible printers added —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/ → —
    • compatible prints added —
    • compatible prints condition added —
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament deretract speed added nil
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed 0 → 11
    • filament minimal purge on wipe tower 90 → 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • filament vendor removed Generic
    • filament wipe added nil
    • full fan speed layer added 0
    • slow down layer time 20 → 5
    • slow down min speed 15 → 10
    • start filament gcode added ; Filament gcode
  45. via parent v17 of *common* — updated
    2026-05-19 11:00
    Identity / metadata
    • Material: OTHER → PLA
    Settings (46)
    • bridge fan speed added 100
    • close fan the first x layers added 2
    • compatible printers condition added —
    • compatible prints added —
    • compatible prints condition added —
    • cooling 0 → 1
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan always on added 1
    • fan cooling layer time added 60
    • fan max speed added 100
    • fan min speed added 35
    • filament colour added #29B2B2
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament deretract speed added nil
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament toolchange delay added 0
    • filament type added PLA
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • filament wipe added nil
    • full fan speed layer added 0
    • hot plate temp added 60
    • hot plate temp initial layer added 60
    • nozzle temperature added 210
    • nozzle temperature initial layer added 210
    • slow down layer time 0 → 5
    • slow down min speed 15 → 10
    • start filament gcode added ; Filament gcode
  46. via parent v16 of *common* — updated
    2026-05-19 05:32
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (5)
    • compatible printers added —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • filament minimal purge on wipe tower removed 90
    • filament vendor removed Generic
    • slow down layer time 20 → 0
  47. via parent v10 of *ABS* — updated
    2026-05-19 05:32
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (34)
    • bridge fan speed added 30
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_RIGID3D.*/ and printer_notes=~/.*PRINTER_HAS_HEATEDBED.*/ → printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • cooling 1 → 0
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time 60 → 20
    • filament colour added #DDDDDD
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 0 → 20
    • filament density added 1.04
    • filament deretract speed removed nil
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower 15 → 90
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament spool weight removed 0
    • filament vendor added Generic
    • filament wipe removed nil
    • hot plate temp added 100
    • hot plate temp initial layer added 100
    • nozzle temperature added 245
    • nozzle temperature initial layer added 245
    • slow down layer time 10 → 20
    • slow down min speed 10 → 15
    • start filament gcode removed ; Filament gcode
    • top fan speed added 0
  48. via parent v15 of *common* — updated
    2026-05-19 05:32
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (26)
    • close fan the first x layers removed 3
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • cooling added 0
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time removed 60
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament density added 0
    • filament deretract speed removed nil
    • filament minimal purge on wipe tower 15 → 90
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament spool weight removed 0
    • filament vendor added Generic
    • filament wipe removed nil
    • slow down layer time 10 → 20
    • slow down min speed 10 → 15
    • start filament gcode removed ; Filament gcode
  49. via parent v9 of *ABS* — updated
    2026-05-19 05:32
    Settings (33)
    • bridge fan speed removed 30
    • close fan the first x layers 2 → 3
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/ → printer_notes=~/.*PRINTER_VENDOR_RIGID3D.*/ and printer_notes=~/.*PRINTER_HAS_HEATEDBED.*/
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time 20 → 60
    • filament colour removed #DDDDDD
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 20 → 0
    • filament density removed 1.04
    • filament deretract speed added nil
    • filament minimal purge on wipe tower added 15
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament wipe added nil
    • hot plate temp removed 90
    • hot plate temp initial layer removed 90
    • nozzle temperature removed 255
    • nozzle temperature initial layer removed 255
    • slow down layer time 8 → 10
    • slow down min speed 30 → 10
    • start filament gcode added ; Filament gcode
    • top fan speed removed 0
  50. via parent v14 of *common* — updated
    2026-05-19 05:32
    Settings (26)
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • cooling removed 1
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time added 60
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament density removed 0
    • filament deretract speed added nil
    • filament minimal purge on wipe tower added 15
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament wipe added nil
    • slow down layer time 8 → 10
    • slow down min speed 30 → 10
    • start filament gcode added ; Filament gcode
  51. via parent v8 of *ABS* — updated
    2026-05-19 05:18
    Settings (9)
    • close fan the first x layers 3 → 2
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_Artillery.*/ → printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • cooling 0 → 1
    • filament colour #6603FC → #DDDDDD
    • filament max volumetric speed removed 11
    • nozzle temperature 240 → 255
    • nozzle temperature initial layer 240 → 255
    • slow down layer time 15 → 8
    • slow down min speed 15 → 30
  52. via parent v13 of *common* — updated
    2026-05-19 05:18
    Settings (3)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_Artillery.*/ → printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • slow down layer time 15 → 8
    • slow down min speed 15 → 30
  53. via parent v7 of *ABS* — updated
    2026-05-19 05:18
    Settings (8)
    • close fan the first x layers 0 → 3
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Artillery.*/
    • filament colour #DDDDDD → #6603FC
    • hot plate temp 100 → 90
    • hot plate temp initial layer 110 → 90
    • nozzle temperature 245 → 240
    • nozzle temperature initial layer 250 → 240
    • slow down layer time 20 → 15
  54. via parent v12 of *common* — updated
    2026-05-19 05:18
    Settings (4)
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Artillery.*/
    • cooling 0 → 1
    • filament flow ratio 0.9 → 1
    • slow down layer time 20 → 15
  55. via parent v6 of *ABS* — updated
    2026-05-19 05:18
    Settings (4)
    • close fan the first x layers 3 → 0
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • hot plate temp initial layer 100 → 110
    • nozzle temperature initial layer 245 → 250
  56. via parent v11 of *common* — updated
    2026-05-19 05:18
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (15)
    • bridge fan speed removed 100
    • close fan the first x layers removed 3
    • compatible printers added —
    • cooling 1 → 0
    • fan always on removed 0
    • fan cooling layer time removed 10
    • filament colour removed #29B2B2
    • filament cost added 0
    • filament density added 0
    • filament flow ratio 1 → 0.9
    • filament notes added —
    • filament vendor removed Generic
    • full fan speed layer removed 0
    • slow down layer time 5 → 20
    • slow down min speed 10 → 15
  57. via parent v10 of *common* — updated
    2026-05-19 05:18
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (15)
    • bridge fan speed added 100
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • cooling 0 → 1
    • fan always on added 0
    • fan cooling layer time added 10
    • filament colour added #29B2B2
    • filament cost removed 0
    • filament density removed 0
    • filament notes removed —
    • filament vendor added Generic
    • full fan speed layer added 0
    • slow down layer time 20 → 5
    • slow down min speed 15 → 10
  58. via parent v5 of *ABS* — updated
    2026-05-19 05:18
    Settings (17)
    • bridge fan speed 50 → 30
    • compatible printers added —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/ → printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • fan cooling layer time 15 → 20
    • fan max speed 50 → 0
    • fan min speed 20 → 0
    • filament colour #FF8000 → #DDDDDD
    • filament cost 30 → 20
    • filament density 1.27 → 1.04
    • filament max volumetric speed 8 → 11
    • filament soluble added 0
    • hot plate temp 70 → 100
    • hot plate temp initial layer 80 → 100
    • nozzle temperature 235 → 245
    • nozzle temperature initial layer 235 → 245
    • slow down layer time 10 → 20
    • top fan speed added 0
  59. via parent v9 of *common* — updated
    2026-05-19 05:18
    Settings (6)
    • compatible printers added —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/ → printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • filament cost added 0
    • filament density added 0
    • filament soluble added 0
    • slow down layer time 10 → 20
  60. via parent v4 of *ABS* — updated
    2026-05-19 05:18
    Settings (18)
    • bridge fan speed 30 → 50
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ → printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/
    • fan cooling layer time 20 → 15
    • fan max speed 0 → 50
    • fan min speed 0 → 20
    • filament colour #DDDDDD → #FF8000
    • filament cost 20 → 30
    • filament density 1.04 → 1.27
    • filament max volumetric speed 11 → 8
    • filament soluble removed 0
    • hot plate temp 100 → 70
    • hot plate temp initial layer 100 → 80
    • idle temperature removed 180
    • nozzle temperature 245 → 235
    • nozzle temperature initial layer 245 → 235
    • slow down layer time 20 → 10
    • top fan speed removed 0
  61. via parent v8 of *common* — updated
    2026-05-19 05:18
    Settings (6)
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ → printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/
    • filament cost removed 0
    • filament density removed 0
    • filament soluble removed 0
    • slow down layer time 20 → 10
  62. via parent v3 of *ABS* — updated
    2026-05-19 05:17
    Settings (24)
    • bridge fan speed 25 → 30
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/ → printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
    • fan max speed 30 → 0
    • fan min speed 20 → 0
    • filament colour #FFF2EC → #DDDDDD
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 0 → 20
    • filament density 0 → 1.04
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • idle temperature added 180
    • nozzle temperature 255 → 245
    • nozzle temperature initial layer 255 → 245
    • slow down layer time 15 → 20
    • top fan speed added 0
  63. via parent v7 of *common* — updated
    2026-05-19 05:17
    Settings (15)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/ → printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
    • cooling 1 → 0
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • slow down layer time 15 → 20
  64. via parent v2 of *ABS* — updated
    2026-05-19 05:17
    Settings (30)
    • bridge fan speed 30 → 25
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan max speed 0 → 30
    • fan min speed 0 → 20
    • filament colour #DDDDDD → #FFF2EC
    • filament cost 20 → 0
    • filament density 1.04 → 0
    • filament deretract speed removed nil
    • filament ramming parameters 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 → 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament spool weight removed 0
    • filament wipe removed nil
    • full fan speed layer removed 0
    • nozzle temperature 245 → 255
    • nozzle temperature initial layer 245 → 255
    • slow down layer time 5 → 15
    • slow down min speed 10 → 15
    • start filament gcode removed ; Filament gcode
    • top fan speed removed 0
  65. via parent v6 of *common* — updated
    2026-05-19 05:17
    Identity / metadata
    • Vendor: QIDI → Unknown
    • Material: PLA → OTHER
    Settings (70)
    • bridge fan speed removed 100
    • chamber temperature removed 0
    • close fan the first x layers removed 1
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • cooling perimeter transition distance removed 3
    • cooling slowdown logic removed consistent_surface
    • disable rapid cooling fan first layers removed 3
    • enable advance pressure removed 1
    • enable auxiliary fan removed 100
    • enable auxiliary fan unseal removed 0
    • enable dynamic fan speeds removed 0
    • enable volume fan removed 100
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan always on removed 1
    • fan cooling layer time removed 60
    • fan max speed removed 100
    • fan min speed removed 100
    • filament colour removed #3399FF
    • filament cooling final speed 0 → 3.4
    • filament cooling initial speed 0 → 2.2
    • filament cooling moves 0 → 4
    • filament density 1.24 → 0
    • filament deretract speed removed nil
    • filament flow ratio 0.98 → 1
    • filament loading speed 0 → 28
    • filament loading speed start 0 → 3
    • filament max volumetric speed removed 20
    • filament minimal purge on wipe tower 5 → 15
    • filament multitool ramming removed 0
    • filament multitool ramming flow removed 10
    • filament multitool ramming volume removed 10
    • filament purge multiplier removed 100
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament shrink removed 100
    • filament spool weight removed 0
    • filament stamping distance removed 0
    • filament stamping loading speed removed 0
    • filament travel max lift removed nil
    • filament travel ramping lift removed nil
    • filament travel slope removed nil
    • filament type removed PLA
    • filament unloading speed 0 → 90
    • filament unloading speed start 0 → 100
    • filament vendor removed QIDI
    • filament wipe removed nil
    • filament wipe distance removed nil
    • full fan speed layer removed 0
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • idle temperature removed 100
    • nozzle temperature removed 220
    • nozzle temperature initial layer removed 210
    • overhang fan speed 0 removed 0
    • overhang fan speed 1 removed 0
    • overhang fan speed 2 removed 0
    • overhang fan speed 3 removed 0
    • seal print removed 1
    • slow down layer time 8 → 15
    • slow down min speed 20 → 15
    • start filament gcode removed ; Filament gcode M900 K0.02 T0.03
  66. via parent v5 of *common* — updated
    2026-05-19 05:15
    Identity / metadata
    • Vendor: Cocoa Press → QIDI
    • Material: OTHER → PLA
    Settings (54)
    • bridge fan speed 0 → 100
    • chamber temperature added 0
    • close fan the first x layers 3 → 1
    • compatible printers added —
    • compatible printers condition added —
    • compatible prints added —
    • compatible prints condition added —
    • cooling 0 → 1
    • cooling perimeter transition distance added 3
    • cooling slowdown logic added consistent_surface
    • disable rapid cooling fan first layers added 3
    • enable advance pressure added 1
    • enable auxiliary fan added 100
    • enable auxiliary fan unseal added 0
    • enable volume fan added 100
    • fan always on 0 → 1
    • fan min speed 35 → 100
    • filament colour #3D2113 → #3399FF
    • filament cooling final speed 3.4 → 0
    • filament cooling initial speed 2.2 → 0
    • filament cooling moves 4 → 0
    • filament cost 70 → 0
    • filament density 1.2912 → 1.24
    • filament diameter 22.66 → 1.75
    • filament flow ratio 1 → 0.98
    • filament loading speed 28 → 0
    • filament loading speed start 3 → 0
    • filament max volumetric speed 0 → 20
    • filament minimal purge on wipe tower 15 → 5
    • filament multitool ramming added 0
    • filament multitool ramming flow added 10
    • filament multitool ramming volume added 10
    • filament purge multiplier added 100
    • filament shrink added 100
    • filament stamping distance added 0
    • filament stamping loading speed added 0
    • filament travel max lift added nil
    • filament travel ramping lift added nil
    • filament travel slope added nil
    • filament type added PLA
    • filament unloading speed 90 → 0
    • filament unloading speed start 100 → 0
    • filament vendor Cocoa Press → QIDI
    • filament wipe 1 → nil
    • filament wipe distance added nil
    • hot plate temp 0 → 60
    • hot plate temp initial layer 0 → 60
    • idle temperature nil → 100
    • nozzle temperature added 220
    • nozzle temperature initial layer 0 → 210
    • seal print added 1
    • slow down layer time 5 → 8
    • slow down min speed 10 → 20
    • start filament gcode ; Filament gcode → ; Filament gcode M900 K0.02 T0.03
  67. via parent v4 of *common* — updated
    2026-05-19 05:14
    Identity / metadata
    • Vendor: Unknown → Cocoa Press
    Settings (55)
    • bridge fan speed added 0
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/
    • cooling 0,0 → 0
    • enable dynamic fan speeds added 0
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan always on added 0
    • fan cooling layer time added 60
    • fan max speed added 100
    • fan min speed added 35
    • filament colour added #3D2113
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 0,0 → 70
    • filament density 0,0 → 1.2912
    • filament deretract speed added nil
    • filament diameter 1.75,1.75 → 22.66
    • filament flow ratio 1,1 → 1
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament soluble 0,0 → 0
    • filament spool weight added 0
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • filament vendor added Cocoa Press
    • filament wipe added 1
    • full fan speed layer added 0
    • hot plate temp added 0
    • hot plate temp initial layer added 0
    • idle temperature added nil
    • nozzle temperature initial layer added 0
    • overhang fan speed 0 added 0
    • overhang fan speed 1 added 0
    • overhang fan speed 2 added 0
    • overhang fan speed 3 added 0
    • slow down layer time 20,20 → 5
    • slow down min speed 15,15 → 10
    • start filament gcode added ; Filament gcode
  68. via parent v3 of *common* — updated
    2026-05-19 05:14
    Identity / metadata
    • Material: PLA → OTHER
    Settings (49)
    • bridge fan speed removed 100
    • close fan the first x layers removed 1
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • cooling 1 → 0,0
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan always on removed 0
    • fan cooling layer time removed 600
    • fan max speed removed 100
    • fan min speed removed 100
    • filament colour removed #29B2B2
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 24 → 0,0
    • filament density 0 → 0,0
    • filament deretract speed removed nil
    • filament diameter 1.75 → 1.75,1.75
    • filament flow ratio 0.92 → 1,1
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed removed 0
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament soluble 0 → 0,0
    • filament toolchange delay removed 0
    • filament type removed PLA
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • filament wipe removed nil
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • nozzle temperature removed 190
    • nozzle temperature initial layer removed 190
    • slow down layer time 1 → 20,20
    • slow down min speed 30 → 15,15
    • start filament gcode removed ; Filament gcode
  69. via parent v2 of *common* — updated
    2026-05-19 05:14
    Settings (12)
    • close fan the first x layers 2 → 1
    • fan always on 1 → 0
    • fan cooling layer time 60 → 600
    • fan min speed 35 → 100
    • filament cost 0 → 24
    • filament flow ratio 1 → 0.92
    • filament spool weight removed 0
    • full fan speed layer removed 0
    • nozzle temperature 210 → 190
    • nozzle temperature initial layer 210 → 190
    • slow down layer time 5 → 1
    • slow down min speed 10 → 30
  70. via parent v1 of *ABS* — created
    2026-05-19 05:14
    Profile created at this point. No prior version to diff against.
  71. via parent v1 of *common* — created
    2026-05-19 05:14
    Profile created at this point. No prior version to diff against.