Generic ABS

Generic · ABS · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

Generic ABS @base

→

Generic ABS

Compatible printers (9)

Bambu Lab P1S 0.4 nozzle
Bambu Lab P1S 0.6 nozzle
Bambu Lab P1S 0.8 nozzle
Bambu Lab X1 0.4 nozzle
Bambu Lab X1 0.6 nozzle
Bambu Lab X1 0.8 nozzle
Bambu Lab X1 Carbon 0.4 nozzle
Bambu Lab X1 Carbon 0.6 nozzle
Bambu Lab X1 Carbon 0.8 nozzle

Inherited from this (2)

Settings

Basic information

Material variant: ABS inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 240 inherited
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 80 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 3 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 15 overridden
was 16 (inherited)

Retraction

Retraction length (mm): 0.4 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	95 inherited	95 inherited
Engineering Plate	95 inherited	95 inherited
High Temp Plate	95 inherited	95 inherited

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
compatible printers: Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 0.4 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab X1 0.6 nozzle, Bambu Lab X1 0.8 nozzle, Bambu Lab P1S 0.4 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle overridden
description: When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials. inherited
filament id: GFB99 inherited
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 80 inherited
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
setting id: GFSB99 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "95"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "95"
  ],
  "cool_plate_temp": [
    "95"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "3"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "95"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "95"
  ],
  "cool_plate_temp_initial_layer": [
    "95"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "description": "When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.",
  "filament_id": "GFB99",
  "setting_id": "GFSB99",
  "compatible_printers": [
    "Bambu Lab X1 Carbon 0.4 nozzle",
    "Bambu Lab X1 0.4 nozzle",
    "Bambu Lab X1 Carbon 0.6 nozzle",
    "Bambu Lab X1 Carbon 0.8 nozzle",
    "Bambu Lab X1 0.6 nozzle",
    "Bambu Lab X1 0.8 nozzle",
    "Bambu Lab P1S 0.4 nozzle",
    "Bambu Lab P1S 0.6 nozzle",
    "Bambu Lab P1S 0.8 nozzle"
  ],
  "name": "Generic ABS"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:17