Ultrafuse TPU-85A @MK4 0.8

Forward AM · FLEX · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

→

Ultrafuse TPU-85A @MK4

→

Ultrafuse TPU-85A @MK4 0.8

Includes (2)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Inherited from this (2)

Settings

Basic information

Material variant: FLEX inherited
Vendor: Forward AM inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.11 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 215 inherited

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.1 inherited
Max volumetric speed (mm³/s): 8 overridden
was 3 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	40 inherited	40 inherited

Other settings

bridge fan speed: 80 inherited
compatible printers condition: printer_model=~/(MK4|MK4IS|MK4ISMMU3|MK3.9|MK3.9MMU3)/ and nozzle_diameter[0]==0.8 and ! single_extruder_multi_material via *FLEX08PG*
cooling: 1 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #0035EC inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament deretract speed: 20 via *FLEX08PG*
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament notes: Material Description Ultrafuse® TPU 85A comes in its natural white color. Chemical properties (e.g. resistance against particular substances) and tolerance for solvents can be made available, if these factors are relevant for a specific application. Generally, these properties correspond to publicly available data on polyether based TPUs. This material is not FDA conform. Good flexibility at low temperature, good wear performance and good damping behavior are the key features of Ultrafuse® TPU 85A. Printing Recommendations: Ultrafuse TPU can be printed directly onto a clean build plate. A small amount of 3Dlac can make removal easier after printing. inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: 2 via *FLEX08PG*
filament retract before wipe: nil inherited
filament retract layer change: 0 via *FLEX08PG*
filament retract length: 3.5 inherited
filament retract lift: 0 inherited
filament retract speed: 60 via *FLEX08PG*
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament travel max lift: 0.6 via *FLEX08PG*
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: nil inherited
idle temperature: 70 via *FLEX08PG*
start filament gcode: M900 K0 ; Filament gcode M142 S36 ; set heatbreak target temp via *FLEX08PG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    "Material Description\nUltrafuse\u00ae TPU 85A comes in its natural white color. Chemical properties (e.g. resistance against particular substances) and tolerance for solvents can be made available, if these factors are relevant for a specific application. Generally, these properties correspond to publicly available data on polyether based TPUs. This material is not FDA conform. Good flexibility at low temperature, good wear performance and good damping behavior are the key features of Ultrafuse\u00ae TPU 85A.\n\nPrinting Recommendations:\nUltrafuse TPU can be printed directly onto a clean build plate. A small amount of 3Dlac can make removal easier after printing."
  ],
  "filament_colour": [
    "#0035EC"
  ],
  "filament_vendor": [
    "Forward AM"
  ],
  "filament_density": [
    "1.11"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1.1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "M900 K0 ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_model=~/(MK4|MK4IS|MK4ISMMU3|MK3.9|MK3.9MMU3)/ and nozzle_diameter[0]==0.8 and ! single_extruder_multi_material"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_type": [
    "FLEX"
  ],
  "filament_wipe": [
    "nil"
  ],
  "hot_plate_temp": [
    "40"
  ],
  "bridge_fan_speed": [
    "80"
  ],
  "nozzle_temperature": [
    "215"
  ],
  "filament_retract_lift": [
    "0"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_retract_length": [
    "3.5"
  ],
  "filament_deretract_speed": [
    "20"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "40"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "filament_retract_speed": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "idle_temperature": [
    "70"
  ],
  "filament_travel_max_lift": [
    "0.6"
  ],
  "name": "Ultrafuse TPU-85A @MK4 0.8",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:46