Generic TPU for AMS @BBL H2C 0.4 nozzle

Generic · TPU-AMS · 0.40mm nozzle · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Generic TPU for AMS @base

→

Generic TPU for AMS @BBL H2C 0.4 nozzle

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

fdm_filament_template_direct_dual

Compatible printers (1)

Bambu Lab H2C 0.4 nozzle

Settings

Basic information

Material variant: TPU-AMS inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.26 inherited
Cost (/kg): 41.99 inherited

Print temperature

Nozzle (initial layer) (°C): 230 overridden
was 230 (inherited)
Nozzle (other layers) (°C): 230 overridden
was 230 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 100 (inherited)
Fan maximum (%): 50 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 40 overridden
was 100 (inherited)
Slow down if layer below (sec): 10 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 10.5 overridden
was 10.5 (inherited)

Retraction

Retraction length (mm): nil via fdm_filament_template_direct_dual
Retraction speed (mm/s): nil via fdm_filament_template_direct_dual
Deretraction speed (mm/s): nil via fdm_filament_template_direct_dual

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	30 inherited	30 inherited
Engineering Plate	35 overridden was 30	35 overridden was 30
High Temp Plate	35 inherited	35 inherited

Other settings

additional cooling fan speed: 100 overridden
was 70 (inherited)
additional fan full speed layer: 0 inherited
close additional fan first x layers: 1 inherited
compatible printers: Bambu Lab H2C 0.4 nozzle overridden
description: If you are to print a kind of soft TPU, please don't slice with this profile, and it is only for TPU that has high enough hardness (not less than 55D) and is compatible with the AMS. To get better printing quality, please refer to this wiki: TPU printing guide. inherited
filament adaptive volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament bridge speed: 25, 25 via fdm_filament_template_direct_dual
filament change length: 4 overridden
filament change length nc: 4 overridden
filament cooling before tower: 10, 10 overridden
filament enable overhang speed: 1, 1 via fdm_filament_template_direct_dual
filament extruder variant: Direct Drive Standard, Direct Drive High Flow via fdm_filament_template_direct_dual
filament flush temp: 0, 0 via fdm_filament_template_direct_dual
filament flush volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament id: GFU98 inherited
filament is support: 0 inherited
filament long retractions when cut: nil, nil via fdm_filament_template_direct_dual
filament minimal purge on wipe tower: 15 inherited
filament overhang 1 4 speed: 0, 0 via fdm_filament_template_direct_dual
filament overhang 2 4 speed: 50, 50 via fdm_filament_template_direct_dual
filament overhang 3 4 speed: 30, 30 via fdm_filament_template_direct_dual
filament overhang 4 4 speed: 10, 10 via fdm_filament_template_direct_dual
filament overhang totally speed: 10, 10 via fdm_filament_template_direct_dual
filament pre cooling temperature: 200, 200 overridden
filament pre cooling temperature nc: 190, 190 overridden
filament prime volume: 30 overridden
filament prime volume nc: 30 overridden
filament ramming travel time: 20, 20 overridden
filament ramming travel time nc: 20, 20 overridden
filament ramming volumetric speed: 2.63, 2.63 overridden
filament ramming volumetric speed nc: 2.63, 2.63 overridden
filament retract before wipe: nil, nil via fdm_filament_template_direct_dual
filament retract length nc: 14, 14 via fdm_filament_template_direct_dual
filament retract restart extra: nil, nil via fdm_filament_template_direct_dual
filament retract when changing layer: nil, nil via fdm_filament_template_direct_dual
filament retraction distances when cut: nil, nil via fdm_filament_template_direct_dual
filament retraction minimum travel: nil, nil via fdm_filament_template_direct_dual
filament soluble: 0 inherited
filament wipe: nil, nil via fdm_filament_template_direct_dual
filament wipe distance: nil, nil via fdm_filament_template_direct_dual
filament z hop: nil, nil via fdm_filament_template_direct_dual
filament z hop types: nil, nil via fdm_filament_template_direct_dual
first x layer fan speed: 0 overridden
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
long retractions when ec: 1, 1 via fdm_filament_template_direct_dual
nozzle temperature range high: 250 inherited
nozzle temperature range low: 200 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 25% overridden
was 95% (inherited)
override process overhang speed: 0, 0 via fdm_filament_template_direct_dual
pre start fan time: 2 overridden
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
retraction distances when ec: 10, 10 via fdm_filament_template_direct_dual
setting id: GFSU98_10 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0 via fdm_filament_template_direct_dual

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "41.99"
  ],
  "filament_type": [
    "TPU-AMS"
  ],
  "filament_wipe": [
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "35"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "35"
  ],
  "cool_plate_temp": [
    "30"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.26"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "230",
    "230"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1",
    "1"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20",
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "40"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil",
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "35"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "35"
  ],
  "cool_plate_temp_initial_layer": [
    "30"
  ],
  "filament_max_volumetric_speed": [
    "10.5",
    "10.5"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "230",
    "230"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "100"
  ],
  "nozzle_temperature_range_low": [
    "200"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "description": "If you are to print a kind of soft TPU, please don't slice with this profile, and it is only for TPU that has high enough hardness (not less than 55D) and is compatible with the AMS. To get better printing quality, please refer to this wiki: TPU printing guide.",
  "filament_id": "GFU98",
  "filament_flush_temp": [
    "0",
    "0"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil"
  ],
  "filament_bridge_speed": [
    "25",
    "25"
  ],
  "long_retractions_when_ec": [
    "1",
    "1"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "filament_retract_length_nc": [
    "14",
    "14"
  ],
  "filament_overhang_1_4_speed": [
    "0",
    "0"
  ],
  "filament_overhang_2_4_speed": [
    "50",
    "50"
  ],
  "filament_overhang_3_4_speed": [
    "30",
    "30"
  ],
  "filament_overhang_4_4_speed": [
    "10",
    "10"
  ],
  "retraction_distances_when_ec": [
    "10",
    "10"
  ],
  "filament_cooling_before_tower": [
    "10",
    "10"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_enable_overhang_speed": [
    "1",
    "1"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_overhang_totally_speed": [
    "10",
    "10"
  ],
  "filament_ramming_travel_time_nc": [
    "20",
    "20"
  ],
  "override_process_overhang_speed": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "200",
    "200"
  ],
  "filament_ramming_volumetric_speed": [
    "2.63",
    "2.63"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil"
  ],
  "filament_pre_cooling_temperature_nc": [
    "190",
    "190"
  ],
  "filament_ramming_volumetric_speed_nc": [
    "2.63",
    "2.63"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil"
  ],
  "setting_id": "GFSU98_10",
  "pre_start_fan_time": [
    "2"
  ],
  "compatible_printers": [
    "Bambu Lab H2C 0.4 nozzle"
  ],
  "filament_prime_volume": [
    "30"
  ],
  "filament_change_length": [
    "4"
  ],
  "first_x_layer_fan_speed": [
    "0"
  ],
  "filament_prime_volume_nc": [
    "30"
  ],
  "filament_change_length_nc": [
    "4"
  ],
  "filament_ramming_travel_time": [
    "20",
    "20"
  ],
  "name": "Generic TPU for AMS @BBL H2C 0.4 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:17