Ultrafuse PAHT-CF15 @XL 0.6

Forward AM · PA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

Fillamentum Nylon FX256

→

Ultrafuse PA

→

Ultrafuse PA6 GF30

→

Ultrafuse PAHT-CF15

→

Ultrafuse PAHT-CF15 @PG 0.6

→

Ultrafuse PAHT-CF15 @XL 0.6

Includes (3)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: PA inherited
Vendor: Forward AM inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.23 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 270 inherited
Nozzle (other layers) (°C): 270 inherited

Cooling

Fan minimum (%): 0 inherited
Fan maximum (%): 50 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 7 via *PA06XL*

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 inherited	105 via include

Other settings

bridge fan speed: 100 inherited
compatible printers condition: printer_model=~/.*XL.*/ and nozzle_diameter[0]==0.6 via *PA06XL*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *PA06XL*
cooling slowdown logic: consistent_surface via *PA06XL*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #404040 inherited
filament cooling final speed: 2.5 via *PA06PG*
filament cooling initial speed: 5 via *PA06PG*
filament cooling moves: 3 via *PA06PG*
filament deretract speed: 30 inherited
filament infill max crossing speed: 140 via *PA06PG*
filament infill max speed: 0 via *PA06PG*
filament load time: 10.5 via *PA06PG*
filament loading speed: 10 via *PA06PG*
filament loading speed start: 50 via *PA06PG*
filament minimal purge on wipe tower: 35 via *PA06XL*
filament multitool ramming: 1 via *PA06XL*
filament multitool ramming flow: 40 via *PA06XL*
filament multitool ramming volume: 5 via *PA06XL*
filament notes: Material Description PAHT CF15 is a high-performance 3D printing filament that opens new application fields in FFF printing. In parallel to its advanced mechanical properties, dimensional stability, and chemical resistance, it has very good processability. It works in any FFF printer with a hardened nozzle. In addition to that, it is compatible with water-soluble support material and HiPS, which allow printing complex geometries that work in challenging environments. PAHT CF15 has high heat resistance up to 130 °C and low moisture absorption. Printing Recommendations: This material contains fibers that have an abrasive effect on printer components. Use a hardened nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle. Ultrafuse PAHT-CF can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion. inherited
filament ramming parameters: 250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 via *PA06PG*
filament retract before travel: 2 inherited
filament retract layer change: 0 inherited
filament retract length: 1.2 inherited
filament retract length toolchange: 20 via *PA06XL*
filament retract lift: nil inherited
filament retract speed: 40 inherited
filament soluble: 0 inherited
filament spool weight: 0 inherited
filament stamping distance: 45 via *PA06PG*
filament stamping loading speed: 26.5 via *PA06PG*
filament toolchange delay: 0 via *PA06PG*
filament travel max lift: 1.5 via *PA06XL*
filament travel ramping lift: 1 via *PA06XL*
filament travel slope: 1 via *PA06XL*
filament unload time: 8.5 via *PA06PG*
filament unloading speed: 60 via *PA06PG*
filament unloading speed start: 60 via *PA06PG*
filament wipe: 0 inherited
full fan speed layer: 3 inherited
idle temperature: 70 via *PA06XL*
start filament gcode: {if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/} M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Legacy LA {else} M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.6}0.025{elsif nozzle_diameter[filament_extruder_id]==0.8}0.016{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Pressure advance {endif} M142 S45 ; set heatbreak target temp via *PA06PG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    "Material Description\nPAHT CF15 is a high-performance 3D printing filament that opens new application fields in FFF printing. In parallel to its advanced mechanical properties, dimensional stability, and chemical resistance, it has very good processability. It works in any FFF printer with a hardened nozzle. In addition to that, it is compatible with water-soluble support material and HiPS, which allow printing complex geometries that work in challenging environments. PAHT CF15 has high heat resistance up to 130 \u00b0C and low moisture absorption.\n\nPrinting Recommendations:\nThis material contains fibers that have an abrasive effect on printer components. Use a hardened nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle.\n\nUltrafuse PAHT-CF can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion."
  ],
  "filament_colour": [
    "#404040"
  ],
  "filament_vendor": [
    "Forward AM"
  ],
  "filament_density": [
    "1.23"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.6}0.025{elsif nozzle_diameter[filament_extruder_id]==0.8}0.016{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S45 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
  ],
  "filament_cooling_final_speed": [
    "2.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_model=~/.*XL.*/ and nozzle_diameter[0]==0.6"
  ],
  "filament_max_volumetric_speed": [
    "7"
  ],
  "filament_cooling_initial_speed": [
    "5"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_type": [
    "PA"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "filament_spool_weight": [
    "0"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "filament_retract_length": [
    "1.2"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "filament_wipe": [
    "0"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "filament_retract_speed": [
    "40"
  ],
  "filament_deretract_speed": [
    "30"
  ],
  "idle_temperature": [
    "70"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_stamping_loading_speed": [
    "26.5"
  ],
  "filament_infill_max_crossing_speed": [
    "140"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "1.5"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_multitool_ramming_flow": [
    "40"
  ],
  "filament_multitool_ramming_volume": [
    "5"
  ],
  "filament_retract_length_toolchange": [
    "20"
  ],
  "name": "Ultrafuse PAHT-CF15 @XL 0.6",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:46