Ultrafuse PET @COREONE HF0.5

Forward AM · PET · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

→

→

Ultrafuse PET @COREONE HF0.5

Includes (4)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: PET inherited
Vendor: Forward AM inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.33 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 215 inherited
Chamber (°C): 35 via *PET05HFC1*

Cooling

Fan minimum (%): 55 overridden
was 75 (inherited)
Fan maximum (%): 75 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 25 via *PET05HFC1*
Slow down if layer below (sec): 10 via *PET05HFC1*
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 24 via *PET05HF*

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	70 inherited	70 inherited

Other settings

bridge fan speed: 75 overridden
was 100 (inherited)
chamber minimal temperature: 0 via *PET05HFC1*
compatible printers condition: printer_model=~/(COREONE|COREONEOAK|COREONEMMU3|COREONEL|COREONELMMU3)/ and nozzle_diameter[0]==0.5 and nozzle_high_flow[0] via *PET05HFC1*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *PET05HF*
cooling slowdown logic: consistent_surface via *PET05HF*
enable dynamic fan speeds: 1 via *PET05HFC1*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #F7F7F7 inherited
filament cooling final speed: 2.5 via *PET05HF*
filament cooling initial speed: 5 via *PET05HF*
filament cooling moves: 3 via *PET05HF*
filament infill max crossing speed: 120 via *PET05HF*
filament infill max speed: 200 via *PET05HF*
filament load time: 10.9 via *PET05HFC1*
filament loading speed: 10 via *PET05HF*
filament loading speed start: 50 via *PET05HF*
filament minimal purge on wipe tower: 35 via *PET05HF*
filament notes: Material Description Ultrafuse PET is made from a premium PET and prints as easy as PLA, but is much stronger. The filament has a large operating window for printing (temperature vs. speed), so it can be used on every 3D-printer. PET will give you outstanding printing results: a good layer adhesion, a high resolution and it is easy to handle. Ultrafuse PET can be 100% recycled, is watertight and has great colors and finish. Printing Recommendations: Ultrafuse PET can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion. inherited
filament ramming parameters: 250 100 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 via *PET05HF*
filament retract before travel: 2 inherited
filament retract before wipe: 20 via *PET05HF*
filament retract layer change: 0 inherited
filament retract length: 0.8 via *PET05HF*
filament retract lift: 0.15 via *PET05HF*
filament retract speed: 40 inherited
filament soluble: 0 inherited
filament stamping distance: 45 via *PET05HF*
filament stamping loading speed: 26.5 via *PET05HF*
filament toolchange delay: 0 via *PET05HF*
filament travel max lift: 1.5 via *PET05HF*
filament travel ramping lift: 1 via *PET05HF*
filament travel slope: 1 via *PET05HF*
filament unload time: 8.9 via *PET05HFC1*
filament unloading speed: 60 via *PET05HF*
filament unloading speed start: 60 via *PET05HF*
filament wipe: 1 via *PET05HF*
full fan speed layer: 3 inherited
idle temperature: 130 via *PET05HFC1*
overhang fan speed 0: 75 overridden
overhang fan speed 1: 0 overridden
start filament gcode: M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.047{elsif nozzle_diameter[filament_extruder_id]==0.5}0.042{elsif nozzle_diameter[filament_extruder_id]==0.6}0.033{elsif nozzle_diameter[filament_extruder_id]==0.8}0.021{elsif nozzle_diameter[filament_extruder_id]==0.25}0.17{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Filament gcode M142 S36 ; set heatbreak target temp via *PET05HF*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    ""
  ],
  "filament_notes": [
    "Material Description\nUltrafuse PET is made from a premium PET and prints as easy as PLA, but is much stronger. The filament has a large operating window for printing (temperature vs. speed), so it can be used on every 3D-printer. PET will give you outstanding printing results: a good layer adhesion, a high resolution and it is easy to handle. Ultrafuse PET can be 100% recycled, is watertight and has great colors and finish.\n\nPrinting Recommendations:\nUltrafuse PET can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion."
  ],
  "filament_colour": [
    "#F7F7F7"
  ],
  "filament_vendor": [
    "Forward AM"
  ],
  "filament_density": [
    "1.33"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.9"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.9"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "start_filament_gcode": [
    "M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.047{elsif nozzle_diameter[filament_extruder_id]==0.5}0.042{elsif nozzle_diameter[filament_extruder_id]==0.6}0.033{elsif nozzle_diameter[filament_extruder_id]==0.8}0.021{elsif nozzle_diameter[filament_extruder_id]==0.25}0.17{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
  ],
  "filament_cooling_final_speed": [
    "2.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_model=~/(COREONE|COREONEOAK|COREONEMMU3|COREONEL|COREONELMMU3)/ and nozzle_diameter[0]==0.5 and nozzle_high_flow[0]"
  ],
  "filament_max_volumetric_speed": [
    "24"
  ],
  "filament_cooling_initial_speed": [
    "5"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "75"
  ],
  "fan_min_speed": [
    "55"
  ],
  "filament_type": [
    "PET"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "bridge_fan_speed": [
    "75"
  ],
  "nozzle_temperature": [
    "215"
  ],
  "fan_cooling_layer_time": [
    "25"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "filament_wipe": [
    "1"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "filament_retract_lift": [
    "0.15"
  ],
  "filament_retract_speed": [
    "40"
  ],
  "filament_retract_length": [
    "0.8"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "idle_temperature": [
    "130"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "filament_travel_max_lift": [
    "1.5"
  ],
  "filament_infill_max_speed": [
    "200"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_retract_before_wipe": [
    "20"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_stamping_loading_speed": [
    "26.5"
  ],
  "filament_infill_max_crossing_speed": [
    "120"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "overhang_fan_speed_0": [
    "75"
  ],
  "enable_dynamic_fan_speeds": [
    "1"
  ],
  "chamber_temperature": [
    "35"
  ],
  "chamber_minimal_temperature": [
    "0"
  ],
  "overhang_fan_speed_1": [
    "0"
  ],
  "name": "Ultrafuse PET @COREONE HF0.5",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:45