slicershare (test)
← addnorth Textura @PG 0.8

History of addnorth Textura @PG 0.8

Direct edits to this profile, and edits to any profile it inherits from. An inherited change can shift this profile's effective behavior even when this profile itself wasn't touched.

Inherits from: *common* → *PLA* → addnorth Textura
  1. direct edit v1 — created
    2026-05-19 11:37
    Profile created at this point. No prior version to diff against.
  2. via parent v40 of *common* — updated
    2026-05-19 11:15
    Settings (19)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_ULTIMAKER.*/ → —
    • cooling 0 → 1
    • end filament gcode added —
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament diameter 2.85 → 1.75
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • slow down layer time 6 → 20
    • slow down min speed 5 → 15
    • start filament gcode added —
  3. via parent v33 of *PLA* — updated
    2026-05-19 11:15
    Settings (19)
    • bridge fan speed added 100
    • close fan the first x layers added 3
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_E2D.*/ → printer_notes=~/.*PRINTER_VENDOR_ULTIMAKER.*/
    • fan cooling layer time added 100
    • fan max speed added 100
    • fan min speed added 100
    • filament colour added #C0C0C0
    • filament cost added 0
    • filament density added 1.24
    • filament diameter 1.75 → 2.85
    • filament flow ratio added 1
    • filament max volumetric speed added 0
    • filament notes added —
    • filament soluble added 0
    • hot plate temp initial layer 60 → 55
    • nozzle temperature 195 → 210
    • nozzle temperature initial layer 200 → 205
    • slow down layer time added 6
    • slow down min speed 90 → 5
  4. via parent v39 of *common* — updated
    2026-05-19 11:15
    Settings (10)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_E2D.*/ → printer_notes=~/.*PRINTER_VENDOR_ULTIMAKER.*/
    • cooling added 0
    • filament cost added 0
    • filament density added 0
    • filament diameter 1.75 → 2.85
    • filament flow ratio added 1
    • filament notes added —
    • filament soluble added 0
    • slow down layer time added 6
    • slow down min speed added 5
  5. via parent v32 of *PLA* — updated
    2026-05-19 11:15
    Settings (32)
    • bridge fan speed removed 100
    • close fan the first x layers removed 1
    • compatible printers condition ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) and printer_notes!~/.*PG.*/ → printer_notes=~/.*PRINTER_VENDOR_E2D.*/
    • end filament gcode removed ; Filament-specific end gcode
    • fan cooling layer time removed 100
    • fan max speed removed 100
    • fan min speed removed 100
    • filament colour removed #FF8000
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost removed 0
    • filament density removed 0
    • filament flow ratio removed 1
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed removed 15
    • filament minimal purge on wipe tower removed 15
    • filament notes removed —
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament soluble removed 0
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • full fan speed layer removed 4
    • nozzle temperature 210 → 195
    • nozzle temperature initial layer 215 → 200
    • slow down layer time removed 12
    • slow down min speed 15 → 90
    • start filament gcode removed {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.17{elsif nozzle_diameter[0]==0.8}0.12{elsif nozzle_diameter[0]==0.4}0.27{elsif nozzle_diameter[0]==0.25}0.85{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.035{elsif nozzle_diameter[0]==0.5}0.025{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.014{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.08{else}0{endif} ; Filament gcode {endif}
  6. via parent v38 of *common* — updated
    2026-05-19 11:15
    Settings (23)
    • compatible printers condition ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) and printer_notes!~/.*PG.*/ → printer_notes=~/.*PRINTER_VENDOR_E2D.*/
    • cooling removed 1
    • end filament gcode removed ; Filament-specific end gcode
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost removed 0
    • filament density removed 0
    • filament flow ratio removed 1
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament minimal purge on wipe tower removed 15
    • filament notes removed —
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament soluble removed 0
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • slow down layer time removed 15
    • slow down min speed removed 15
    • start filament gcode removed M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif} ; Filament gcode
  7. via parent v2 of addnorth Textura — updated
    2026-05-19 11:10
    Settings (12)
    • compatible printers condition printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1) → printer_model!="MK2SMM" and printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)
    • filament cooling final speed 2 → 3.4
    • filament cooling initial speed 3 → 2.2
    • filament cooling moves 1 → 4
    • filament loading speed 14 → 28
    • filament loading speed start 19 → 3
    • filament max volumetric speed 0 → 15
    • filament minimal purge on wipe tower 0 → 15
    • filament ramming parameters 130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6 → 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract length added 1
    • filament unloading speed 20 → 90
    • start filament gcode — → {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.17{elsif nozzle_diameter[0]==0.8}0.12{elsif nozzle_diameter[0]==0.4}0.27{elsif nozzle_diameter[0]==0.25}0.85{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.035{elsif nozzle_diameter[0]==0.5}0.025{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.014{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.08{else}0{endif} ; Filament gcode {endif}
  8. via parent v31 of *PLA* — updated
    2026-05-19 11:08
    Settings (30)
    • bridge fan speed 70 → 100
    • close fan the first x layers 2 → 1
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_HSP.*/ → ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) and printer_notes!~/.*PG.*/
    • end filament gcode added ; Filament-specific end gcode
    • fan cooling layer time 60 → 100
    • fan max speed 70 → 100
    • fan min speed 70 → 100
    • filament colour #FF3232 → #FF8000
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 20 → 0
    • filament density 1.24 → 0
    • filament flow ratio 0.94 → 1
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • full fan speed layer added 4
    • full fan speed layers removed 6
    • idle temperature removed 140
    • nozzle temperature 205 → 210
    • nozzle temperature initial layer 195 → 215
    • slow down layer time 10 → 12
    • start filament gcode added {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.04{else}0.05{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K18{elsif nozzle_diameter[0]==0.8};{else}M900 K30{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.17{elsif nozzle_diameter[0]==0.8}0.12{elsif nozzle_diameter[0]==0.4}0.27{elsif nozzle_diameter[0]==0.25}0.85{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.035{elsif nozzle_diameter[0]==0.5}0.025{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.014{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.08{else}0{endif} ; Filament gcode {endif}
  9. via parent v37 of *common* — updated
    2026-05-19 11:08
    Settings (18)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_HSP.*/ → ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) and printer_notes!~/.*PG.*/
    • cooling 0 → 1
    • end filament gcode added ; Filament-specific end gcode
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament flow ratio added 1
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • slow down layer time 10 → 15
    • start filament gcode added M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}200{else}30{endif} ; Filament gcode
  10. via parent v30 of *PLA* — updated
    2026-05-19 11:08
    Settings (31)
    • bridge fan speed 100 → 70
    • close fan the first x layers 1 → 2
    • compatible printers condition printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1) → printer_notes=~/.*PRINTER_VENDOR_HSP.*/
    • end filament gcode removed ; Filament-specific end gcode
    • fan cooling layer time 100 → 60
    • fan max speed 100 → 70
    • fan min speed 100 → 70
    • filament colour #FF8000 → #FF3232
    • filament cooling final speed removed 2
    • filament cooling initial speed removed 3
    • filament cooling moves removed 1
    • filament cost 0 → 20
    • filament density 0 → 1.24
    • filament flow ratio 1 → 0.94
    • filament load time removed 0
    • filament loading speed removed 14
    • filament loading speed start removed 19
    • filament max volumetric speed 0 → 15
    • filament minimal purge on wipe tower removed 0
    • filament ramming parameters removed 130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 20
    • filament unloading speed start removed 100
    • full fan speed layer removed 3
    • full fan speed layers added 6
    • idle temperature added 140
    • nozzle temperature 210 → 205
    • nozzle temperature initial layer 215 → 195
    • slow down min speed 10 → 15
    • start filament gcode removed —
  11. via parent v36 of *common* — updated
    2026-05-19 11:08
    Settings (18)
    • compatible printers condition printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1) → printer_notes=~/.*PRINTER_VENDOR_HSP.*/
    • cooling 1 → 0
    • end filament gcode removed ; Filament-specific end gcode
    • filament cooling final speed removed 2
    • filament cooling initial speed removed 3
    • filament cooling moves removed 1
    • filament flow ratio removed 1
    • filament load time removed 0
    • filament loading speed removed 14
    • filament loading speed start removed 19
    • filament minimal purge on wipe tower removed 0
    • filament ramming parameters removed 130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 20
    • filament unloading speed start removed 100
    • slow down min speed 10 → 15
    • start filament gcode removed —
  12. via parent v1 of addnorth Textura — created
    2026-05-19 11:07
    Profile created at this point. No prior version to diff against.
  13. via parent v29 of *PLA* — updated
    2026-05-19 11:06
    Settings (24)
    • close fan the first x layers 3 → 1
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_BIBO.*/ → printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
    • end filament gcode added ; Filament-specific end gcode
    • filament colour #FF3232 → #FF8000
    • filament cooling final speed added 2
    • filament cooling initial speed added 3
    • filament cooling moves added 1
    • filament cost 20 → 0
    • filament density 1.24 → 0
    • filament load time added 0
    • filament loading speed added 14
    • filament loading speed start added 19
    • filament max volumetric speed 15 → 0
    • filament minimal purge on wipe tower 15 → 0
    • filament ramming parameters 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 → 130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 20
    • filament unloading speed start added 100
    • full fan speed layer added 3
    • nozzle temperature 200 → 210
    • slow down layer time 20 → 10
    • slow down min speed 15 → 10
    • start filament gcode added —
  14. via parent v35 of *common* — updated
    2026-05-19 11:06
    Settings (18)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_BIBO.*/ → printer_notes!~/.*NO_TEMPLATES.*/ and printer_notes!~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes!~/.*PRINTER_MODEL_MK4IS.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and num_extruders>1)
    • cooling 0 → 1
    • end filament gcode added ; Filament-specific end gcode
    • filament cooling final speed added 2
    • filament cooling initial speed added 3
    • filament cooling moves added 1
    • filament load time added 0
    • filament loading speed added 14
    • filament loading speed start added 19
    • filament minimal purge on wipe tower 15 → 0
    • filament ramming parameters 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 → 130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 20
    • filament unloading speed start added 100
    • slow down layer time 20 → 10
    • slow down min speed 15 → 10
    • start filament gcode added —
  15. via parent v28 of *PLA* — updated
    2026-05-19 11:06
    Settings (7)
    • close fan the first x layers 1 → 3
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_ELEGOO.*/ → printer_notes=~/.*PRINTER_VENDOR_BIBO.*/
    • filament colour #DDDDDD → #FF3232
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • nozzle temperature 205 → 200
    • nozzle temperature initial layer 210 → 215
  16. via parent v34 of *common* — updated
    2026-05-19 11:06
    Settings (3)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_ELEGOO.*/ → printer_notes=~/.*PRINTER_VENDOR_BIBO.*/
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
  17. via parent v27 of *PLA* — updated
    2026-05-19 11:06
    Settings (5)
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_ELEGOO.*/
    • filament colour added #DDDDDD
    • nozzle temperature 200 → 205
    • nozzle temperature initial layer 200 → 210
    • slow down layer time 0 → 20
  18. via parent v33 of *common* — updated
    2026-05-19 11:06
    Settings (2)
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_ELEGOO.*/
    • slow down layer time 0 → 20
  19. via parent v26 of *PLA* — updated
    2026-05-19 11:05
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (10)
    • close fan the first x layers 2 → 1
    • compatible printers added —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • filament colour removed #DDDDDD
    • filament max volumetric speed 0 → 15
    • filament minimal purge on wipe tower removed 90
    • filament vendor removed Generic
    • nozzle temperature 205 → 200
    • nozzle temperature initial layer 210 → 200
    • slow down layer time 20 → 0
  20. via parent v32 of *common* — updated
    2026-05-19 11:05
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (5)
    • compatible printers added —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • filament minimal purge on wipe tower removed 90
    • filament vendor removed Generic
    • slow down layer time 20 → 0
  21. via parent v25 of *PLA* — updated
    2026-05-19 11:05
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (33)
    • close fan the first x layers 3 → 2
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_RIGID3D.*/ → printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time 60 → 100
    • filament colour added #DDDDDD
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 0 → 20
    • filament density added 1.24
    • filament deretract speed removed nil
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower 15 → 90
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament spool weight removed 0
    • filament vendor added Generic
    • filament wipe removed nil
    • full fan speed layer removed 4
    • hot plate temp added 60
    • hot plate temp initial layer added 60
    • nozzle temperature added 205
    • nozzle temperature initial layer added 210
    • slow down layer time 10 → 20
    • slow down min speed 10 → 15
    • start filament gcode removed ; Filament gcode
  22. via parent v31 of *common* — updated
    2026-05-19 11:05
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (26)
    • close fan the first x layers removed 3
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • cooling added 0
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time removed 60
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament density added 0
    • filament deretract speed removed nil
    • filament minimal purge on wipe tower 15 → 90
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament spool weight removed 0
    • filament vendor added Generic
    • filament wipe removed nil
    • slow down layer time 10 → 20
    • slow down min speed 10 → 15
    • start filament gcode removed ; Filament gcode
  23. via parent v24 of *PLA* — updated
    2026-05-19 11:05
    Settings (32)
    • close fan the first x layers 1 → 3
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/ → printer_notes=~/.*PRINTER_VENDOR_RIGID3D.*/
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time 100 → 60
    • filament colour removed #DDDDDD
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 20 → 0
    • filament density removed 1.24
    • filament deretract speed added nil
    • filament minimal purge on wipe tower added 15
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament wipe added nil
    • full fan speed layer added 4
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • nozzle temperature removed 200
    • nozzle temperature initial layer removed 230
    • slow down layer time 8 → 10
    • slow down min speed 30 → 10
    • start filament gcode added ; Filament gcode
  24. via parent v30 of *common* — updated
    2026-05-19 11:05
    Settings (26)
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • cooling removed 1
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time added 60
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament density removed 0
    • filament deretract speed added nil
    • filament minimal purge on wipe tower added 15
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament wipe added nil
    • slow down layer time 8 → 10
    • slow down min speed 30 → 10
    • start filament gcode added ; Filament gcode
  25. via parent v23 of *PLA* — updated
    2026-05-19 11:05
    Settings (9)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_Artillery.*/ → printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • filament colour #428AF5 → #DDDDDD
    • filament max volumetric speed removed 15
    • full fan speed layer removed 3
    • hot plate temp initial layer 65 → 60
    • nozzle temperature 205 → 200
    • nozzle temperature initial layer 210 → 230
    • slow down layer time 15 → 8
    • slow down min speed 15 → 30
  26. via parent v29 of *common* — updated
    2026-05-19 11:05
    Settings (3)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_Artillery.*/ → printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • slow down layer time 15 → 8
    • slow down min speed 15 → 30
  27. via parent v22 of *PLA* — updated
    2026-05-19 11:05
    Settings (8)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_MAKERGEAR.*/ and printer_notes=~/.*PRINTER_MODEL_MAKERGEAR_(U1|M(ICRO|2|2_DUAL|3_SE|3_ID|3_ID_DUPLICATION)).*/ → printer_notes=~/.*PRINTER_VENDOR_Artillery.*/
    • filament colour #DDDDDD → #428AF5
    • filament flow ratio 0.9 → 1
    • full fan speed layer added 3
    • hot plate temp initial layer 60 → 65
    • nozzle temperature 210 → 205
    • nozzle temperature initial layer 215 → 210
    • slow down layer time 20 → 15
  28. via parent v28 of *common* — updated
    2026-05-19 11:05
    Settings (4)
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Artillery.*/
    • cooling 0 → 1
    • filament flow ratio 0.9 → 1
    • slow down layer time 20 → 15
  29. via parent v21 of *PLA* — updated
    2026-05-19 11:05
    Settings (4)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_BIQU.*/ → printer_notes=~/.*PRINTER_VENDOR_MAKERGEAR.*/ and printer_notes=~/.*PRINTER_MODEL_MAKERGEAR_(U1|M(ICRO|2|2_DUAL|3_SE|3_ID|3_ID_DUPLICATION)).*/
    • filament flow ratio 1 → 0.9
    • nozzle temperature 205 → 210
    • nozzle temperature initial layer 210 → 215
  30. via parent v27 of *common* — updated
    2026-05-19 11:05
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (15)
    • bridge fan speed removed 100
    • close fan the first x layers removed 3
    • compatible printers added —
    • cooling 1 → 0
    • fan always on removed 0
    • fan cooling layer time removed 10
    • filament colour removed #29B2B2
    • filament cost added 0
    • filament density added 0
    • filament flow ratio 1 → 0.9
    • filament notes added —
    • filament vendor removed Generic
    • full fan speed layer removed 0
    • slow down layer time 5 → 20
    • slow down min speed 10 → 15
  31. via parent v26 of *common* — updated
    2026-05-19 11:04
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (15)
    • bridge fan speed added 100
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • cooling 0 → 1
    • fan always on added 0
    • fan cooling layer time added 10
    • filament colour added #29B2B2
    • filament cost removed 0
    • filament density removed 0
    • filament notes removed —
    • filament vendor added Generic
    • full fan speed layer added 0
    • slow down layer time 20 → 5
    • slow down min speed 15 → 10
  32. via parent v20 of *PLA* — updated
    2026-05-19 11:04
    Settings (20)
    • bridge fan speed 80 → 100
    • compatible printers added —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/ → printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • fan cooling layer time 15 → 100
    • fan max speed 80 → 100
    • fan min speed 40 → 100
    • filament colour #FF3232 → #DDDDDD
    • filament cooling moves removed 0
    • filament flow ratio 0.94 → 1
    • filament loading speed removed 30
    • filament loading speed start removed 30
    • filament max volumetric speed 0 → 15
    • filament ramming parameters removed 0
    • filament soluble added 0
    • filament unload time removed 0
    • filament unloading speed removed 30
    • filament unloading speed start removed 30
    • nozzle temperature 200 → 205
    • nozzle temperature initial layer 200 → 210
    • slow down layer time 10 → 20
  33. via parent v25 of *common* — updated
    2026-05-19 11:04
    Settings (6)
    • compatible printers added —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/ → printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • filament cost added 0
    • filament density added 0
    • filament soluble added 0
    • slow down layer time 10 → 20
  34. via parent v19 of *PLA* — updated
    2026-05-19 11:04
    Settings (21)
    • bridge fan speed 100 → 80
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ → printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/
    • fan cooling layer time 100 → 15
    • fan max speed 100 → 80
    • fan min speed 100 → 40
    • filament colour #DDDDDD → #FF3232
    • filament cooling moves added 0
    • filament flow ratio 1 → 0.94
    • filament loading speed added 30
    • filament loading speed start added 30
    • filament max volumetric speed 15 → 0
    • filament ramming parameters added 0
    • filament soluble removed 0
    • filament unload time added 0
    • filament unloading speed added 30
    • filament unloading speed start added 30
    • idle temperature removed 150
    • nozzle temperature 205 → 200
    • nozzle temperature initial layer 210 → 200
    • slow down layer time 20 → 10
  35. via parent v24 of *common* — updated
    2026-05-19 11:04
    Settings (6)
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ → printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/
    • filament cost removed 0
    • filament density removed 0
    • filament soluble removed 0
    • slow down layer time 20 → 10
  36. via parent v18 of *PLA* — updated
    2026-05-19 11:04
    Settings (21)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/ → printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
    • filament colour #FF8000 → #DDDDDD
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 0 → 20
    • filament density 0 → 1.24
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • full fan speed layer removed 4
    • idle temperature added 150
    • nozzle temperature 210 → 205
    • nozzle temperature initial layer 215 → 210
    • slow down layer time 15 → 20
  37. via parent v23 of *common* — updated
    2026-05-19 11:04
    Settings (15)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/ → printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
    • cooling 1 → 0
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • slow down layer time 15 → 20
  38. via parent v17 of *PLA* — updated
    2026-05-19 11:03
    Identity / metadata
    • Material: PLA,PLA → PLA
    Settings (35)
    • bridge fan speed 100,100 → 100
    • close fan the first x layers 1,1 → 1
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/ → printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/
    • cooling 1,1 → 1
    • fan always on 1,1 → 1
    • fan cooling layer time 100,100 → 100
    • fan max speed 100,100 → 100
    • fan min speed 100,100 → 100
    • filament colour #DDDDDD,#DDDDDD → #FF8000
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 20,20 → 0
    • filament density 1.24,1.24 → 0
    • filament diameter 1.75,1.75 → 1.75
    • filament flow ratio 1,1 → 1
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed 15,15 → 15
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament soluble 0,0 → 0
    • filament toolchange delay added 0
    • filament type PLA,PLA → PLA
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • full fan speed layer added 4
    • hot plate temp 60,60 → 60
    • hot plate temp initial layer 60,60 → 60
    • nozzle temperature 205,205 → 210
    • nozzle temperature initial layer 210,210 → 215
    • slow down layer time 20,20 → 15
    • slow down min speed 15,15 → 15
  39. via parent v22 of *common* — updated
    2026-05-19 11:03
    Identity / metadata
    • Vendor: QIDI → Unknown
    • Material: PLA → OTHER
    Settings (70)
    • bridge fan speed removed 100
    • chamber temperature removed 0
    • close fan the first x layers removed 1
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • cooling perimeter transition distance removed 3
    • cooling slowdown logic removed consistent_surface
    • disable rapid cooling fan first layers removed 3
    • enable advance pressure removed 1
    • enable auxiliary fan removed 100
    • enable auxiliary fan unseal removed 0
    • enable dynamic fan speeds removed 0
    • enable volume fan removed 100
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan always on removed 1
    • fan cooling layer time removed 60
    • fan max speed removed 100
    • fan min speed removed 100
    • filament colour removed #3399FF
    • filament cooling final speed 0 → 3.4
    • filament cooling initial speed 0 → 2.2
    • filament cooling moves 0 → 4
    • filament density 1.24 → 0
    • filament deretract speed removed nil
    • filament flow ratio 0.98 → 1
    • filament loading speed 0 → 28
    • filament loading speed start 0 → 3
    • filament max volumetric speed removed 20
    • filament minimal purge on wipe tower 5 → 15
    • filament multitool ramming removed 0
    • filament multitool ramming flow removed 10
    • filament multitool ramming volume removed 10
    • filament purge multiplier removed 100
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament shrink removed 100
    • filament spool weight removed 0
    • filament stamping distance removed 0
    • filament stamping loading speed removed 0
    • filament travel max lift removed nil
    • filament travel ramping lift removed nil
    • filament travel slope removed nil
    • filament type removed PLA
    • filament unloading speed 0 → 90
    • filament unloading speed start 0 → 100
    • filament vendor removed QIDI
    • filament wipe removed nil
    • filament wipe distance removed nil
    • full fan speed layer removed 0
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • idle temperature removed 100
    • nozzle temperature removed 220
    • nozzle temperature initial layer removed 210
    • overhang fan speed 0 removed 0
    • overhang fan speed 1 removed 0
    • overhang fan speed 2 removed 0
    • overhang fan speed 3 removed 0
    • seal print removed 1
    • slow down layer time 8 → 15
    • slow down min speed 20 → 15
    • start filament gcode removed ; Filament gcode M900 K0.02 T0.03
  40. via parent v21 of *common* — updated
    2026-05-19 11:01
    Identity / metadata
    • Vendor: Cocoa Press → QIDI
    • Material: OTHER → PLA
    Settings (54)
    • bridge fan speed 0 → 100
    • chamber temperature added 0
    • close fan the first x layers 3 → 1
    • compatible printers added —
    • compatible printers condition added —
    • compatible prints added —
    • compatible prints condition added —
    • cooling 0 → 1
    • cooling perimeter transition distance added 3
    • cooling slowdown logic added consistent_surface
    • disable rapid cooling fan first layers added 3
    • enable advance pressure added 1
    • enable auxiliary fan added 100
    • enable auxiliary fan unseal added 0
    • enable volume fan added 100
    • fan always on 0 → 1
    • fan min speed 35 → 100
    • filament colour #3D2113 → #3399FF
    • filament cooling final speed 3.4 → 0
    • filament cooling initial speed 2.2 → 0
    • filament cooling moves 4 → 0
    • filament cost 70 → 0
    • filament density 1.2912 → 1.24
    • filament diameter 22.66 → 1.75
    • filament flow ratio 1 → 0.98
    • filament loading speed 28 → 0
    • filament loading speed start 3 → 0
    • filament max volumetric speed 0 → 20
    • filament minimal purge on wipe tower 15 → 5
    • filament multitool ramming added 0
    • filament multitool ramming flow added 10
    • filament multitool ramming volume added 10
    • filament purge multiplier added 100
    • filament shrink added 100
    • filament stamping distance added 0
    • filament stamping loading speed added 0
    • filament travel max lift added nil
    • filament travel ramping lift added nil
    • filament travel slope added nil
    • filament type added PLA
    • filament unloading speed 90 → 0
    • filament unloading speed start 100 → 0
    • filament vendor Cocoa Press → QIDI
    • filament wipe 1 → nil
    • filament wipe distance added nil
    • hot plate temp 0 → 60
    • hot plate temp initial layer 0 → 60
    • idle temperature nil → 100
    • nozzle temperature added 220
    • nozzle temperature initial layer 0 → 210
    • seal print added 1
    • slow down layer time 5 → 8
    • slow down min speed 10 → 20
    • start filament gcode ; Filament gcode → ; Filament gcode M900 K0.02 T0.03
  41. via parent v20 of *common* — updated
    2026-05-19 11:01
    Identity / metadata
    • Vendor: Unknown → Cocoa Press
    Settings (55)
    • bridge fan speed added 0
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/
    • cooling 0,0 → 0
    • enable dynamic fan speeds added 0
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan always on added 0
    • fan cooling layer time added 60
    • fan max speed added 100
    • fan min speed added 35
    • filament colour added #3D2113
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 0,0 → 70
    • filament density 0,0 → 1.2912
    • filament deretract speed added nil
    • filament diameter 1.75,1.75 → 22.66
    • filament flow ratio 1,1 → 1
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament soluble 0,0 → 0
    • filament spool weight added 0
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • filament vendor added Cocoa Press
    • filament wipe added 1
    • full fan speed layer added 0
    • hot plate temp added 0
    • hot plate temp initial layer added 0
    • idle temperature added nil
    • nozzle temperature initial layer added 0
    • overhang fan speed 0 added 0
    • overhang fan speed 1 added 0
    • overhang fan speed 2 added 0
    • overhang fan speed 3 added 0
    • slow down layer time 20,20 → 5
    • slow down min speed 15,15 → 10
    • start filament gcode added ; Filament gcode
  42. via parent v16 of *PLA* — updated
    2026-05-19 11:01
    Identity / metadata
    • Material: PLA → PLA,PLA
    Settings (49)
    • bridge fan speed 100 → 100,100
    • close fan the first x layers 1 → 1,1
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • cooling 1 → 1,1
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan always on 0 → 1,1
    • fan cooling layer time 600 → 100,100
    • fan max speed 100 → 100,100
    • fan min speed 100 → 100,100
    • filament colour #29B2B2 → #DDDDDD,#DDDDDD
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 24 → 20,20
    • filament density 0 → 1.24,1.24
    • filament deretract speed removed nil
    • filament diameter 1.75 → 1.75,1.75
    • filament flow ratio 0.92 → 1,1
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed 0 → 15,15
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament soluble 0 → 0,0
    • filament toolchange delay removed 0
    • filament type PLA → PLA,PLA
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • filament wipe removed nil
    • hot plate temp 60 → 60,60
    • hot plate temp initial layer 60 → 60,60
    • nozzle temperature 190 → 205,205
    • nozzle temperature initial layer 190 → 210,210
    • slow down layer time 1 → 20,20
    • slow down min speed 30 → 15,15
    • start filament gcode removed ; Filament gcode
  43. via parent v19 of *common* — updated
    2026-05-19 11:01
    Identity / metadata
    • Material: PLA → OTHER
    Settings (49)
    • bridge fan speed removed 100
    • close fan the first x layers removed 1
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • cooling 1 → 0,0
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan always on removed 0
    • fan cooling layer time removed 600
    • fan max speed removed 100
    • fan min speed removed 100
    • filament colour removed #29B2B2
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 24 → 0,0
    • filament density 0 → 0,0
    • filament deretract speed removed nil
    • filament diameter 1.75 → 1.75,1.75
    • filament flow ratio 0.92 → 1,1
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed removed 0
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament soluble 0 → 0,0
    • filament toolchange delay removed 0
    • filament type removed PLA
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • filament wipe removed nil
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • nozzle temperature removed 190
    • nozzle temperature initial layer removed 190
    • slow down layer time 1 → 20,20
    • slow down min speed 30 → 15,15
    • start filament gcode removed ; Filament gcode
  44. via parent v15 of *PLA* — updated
    2026-05-19 11:00
    Settings (13)
    • fan always on 1 → 0
    • fan cooling layer time 100 → 600
    • filament colour #DDDDDD → #29B2B2
    • filament cost 20 → 24
    • filament density 1.24 → 0
    • filament flow ratio 1 → 0.92
    • filament max volumetric speed 15 → 0
    • filament spool weight removed 0
    • full fan speed layer removed 0
    • nozzle temperature 205 → 190
    • nozzle temperature initial layer 210 → 190
    • slow down layer time 5 → 1
    • slow down min speed 10 → 30
  45. via parent v18 of *common* — updated
    2026-05-19 11:00
    Settings (12)
    • close fan the first x layers 2 → 1
    • fan always on 1 → 0
    • fan cooling layer time 60 → 600
    • fan min speed 35 → 100
    • filament cost 0 → 24
    • filament flow ratio 1 → 0.92
    • filament spool weight removed 0
    • full fan speed layer removed 0
    • nozzle temperature 210 → 190
    • nozzle temperature initial layer 210 → 190
    • slow down layer time 5 → 1
    • slow down min speed 10 → 30
  46. via parent v14 of *PLA* — updated
    2026-05-19 11:00
    Settings (35)
    • compatible printers condition added —
    • compatible prints added —
    • compatible prints condition added —
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • filament colour added #DDDDDD
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament deretract speed added nil
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • filament wipe added nil
    • full fan speed layer added 0
    • nozzle temperature 200 → 205
    • nozzle temperature initial layer 200 → 210
    • slow down layer time 0 → 5
    • slow down min speed 15 → 10
    • start filament gcode added ; Filament gcode
  47. via parent v17 of *common* — updated
    2026-05-19 11:00
    Identity / metadata
    • Material: OTHER → PLA
    Settings (46)
    • bridge fan speed added 100
    • close fan the first x layers added 2
    • compatible printers condition added —
    • compatible prints added —
    • compatible prints condition added —
    • cooling 0 → 1
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan always on added 1
    • fan cooling layer time added 60
    • fan max speed added 100
    • fan min speed added 35
    • filament colour added #29B2B2
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament deretract speed added nil
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament toolchange delay added 0
    • filament type added PLA
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • filament wipe added nil
    • full fan speed layer added 0
    • hot plate temp added 60
    • hot plate temp initial layer added 60
    • nozzle temperature added 210
    • nozzle temperature initial layer added 210
    • slow down layer time 0 → 5
    • slow down min speed 15 → 10
    • start filament gcode added ; Filament gcode
  48. via parent v13 of *PLA* — updated
    2026-05-19 05:32
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (10)
    • close fan the first x layers 2 → 1
    • compatible printers added —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • filament colour removed #DDDDDD
    • filament max volumetric speed 0 → 15
    • filament minimal purge on wipe tower removed 90
    • filament vendor removed Generic
    • nozzle temperature 205 → 200
    • nozzle temperature initial layer 210 → 200
    • slow down layer time 20 → 0
  49. via parent v16 of *common* — updated
    2026-05-19 05:32
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (5)
    • compatible printers added —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • filament minimal purge on wipe tower removed 90
    • filament vendor removed Generic
    • slow down layer time 20 → 0
  50. via parent v12 of *PLA* — updated
    2026-05-19 05:32
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (33)
    • close fan the first x layers 3 → 2
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_RIGID3D.*/ → printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time 60 → 100
    • filament colour added #DDDDDD
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 0 → 20
    • filament density added 1.24
    • filament deretract speed removed nil
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower 15 → 90
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament spool weight removed 0
    • filament vendor added Generic
    • filament wipe removed nil
    • full fan speed layer removed 4
    • hot plate temp added 60
    • hot plate temp initial layer added 60
    • nozzle temperature added 205
    • nozzle temperature initial layer added 210
    • slow down layer time 10 → 20
    • slow down min speed 10 → 15
    • start filament gcode removed ; Filament gcode
  51. via parent v15 of *common* — updated
    2026-05-19 05:32
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (26)
    • close fan the first x layers removed 3
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Geeetech.*/
    • cooling added 0
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time removed 60
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament density added 0
    • filament deretract speed removed nil
    • filament minimal purge on wipe tower 15 → 90
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament spool weight removed 0
    • filament vendor added Generic
    • filament wipe removed nil
    • slow down layer time 10 → 20
    • slow down min speed 10 → 15
    • start filament gcode removed ; Filament gcode
  52. via parent v11 of *PLA* — updated
    2026-05-19 05:32
    Settings (32)
    • close fan the first x layers 1 → 3
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/ → printer_notes=~/.*PRINTER_VENDOR_RIGID3D.*/
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time 100 → 60
    • filament colour removed #DDDDDD
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 20 → 0
    • filament density removed 1.24
    • filament deretract speed added nil
    • filament minimal purge on wipe tower added 15
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament wipe added nil
    • full fan speed layer added 4
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • nozzle temperature removed 200
    • nozzle temperature initial layer removed 230
    • slow down layer time 8 → 10
    • slow down min speed 30 → 10
    • start filament gcode added ; Filament gcode
  53. via parent v14 of *common* — updated
    2026-05-19 05:32
    Settings (26)
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • cooling removed 1
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan cooling layer time added 60
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament density removed 0
    • filament deretract speed added nil
    • filament minimal purge on wipe tower added 15
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament spool weight added 0
    • filament wipe added nil
    • slow down layer time 8 → 10
    • slow down min speed 30 → 10
    • start filament gcode added ; Filament gcode
  54. via parent v10 of *PLA* — updated
    2026-05-19 05:18
    Settings (9)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_Artillery.*/ → printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • filament colour #428AF5 → #DDDDDD
    • filament max volumetric speed removed 15
    • full fan speed layer removed 3
    • hot plate temp initial layer 65 → 60
    • nozzle temperature 205 → 200
    • nozzle temperature initial layer 210 → 230
    • slow down layer time 15 → 8
    • slow down min speed 15 → 30
  55. via parent v13 of *common* — updated
    2026-05-19 05:18
    Settings (3)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_Artillery.*/ → printer_notes=~/.*PRINTER_VENDOR_ANKERMAKE.*/
    • slow down layer time 15 → 8
    • slow down min speed 15 → 30
  56. via parent v9 of *PLA* — updated
    2026-05-19 05:18
    Settings (8)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_MAKERGEAR.*/ and printer_notes=~/.*PRINTER_MODEL_MAKERGEAR_(U1|M(ICRO|2|2_DUAL|3_SE|3_ID|3_ID_DUPLICATION)).*/ → printer_notes=~/.*PRINTER_VENDOR_Artillery.*/
    • filament colour #DDDDDD → #428AF5
    • filament flow ratio 0.9 → 1
    • full fan speed layer added 3
    • hot plate temp initial layer 60 → 65
    • nozzle temperature 210 → 205
    • nozzle temperature initial layer 215 → 210
    • slow down layer time 20 → 15
  57. via parent v12 of *common* — updated
    2026-05-19 05:18
    Settings (4)
    • compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Artillery.*/
    • cooling 0 → 1
    • filament flow ratio 0.9 → 1
    • slow down layer time 20 → 15
  58. via parent v8 of *PLA* — updated
    2026-05-19 05:18
    Settings (4)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_BIQU.*/ → printer_notes=~/.*PRINTER_VENDOR_MAKERGEAR.*/ and printer_notes=~/.*PRINTER_MODEL_MAKERGEAR_(U1|M(ICRO|2|2_DUAL|3_SE|3_ID|3_ID_DUPLICATION)).*/
    • filament flow ratio 1 → 0.9
    • nozzle temperature 205 → 210
    • nozzle temperature initial layer 210 → 215
  59. via parent v11 of *common* — updated
    2026-05-19 05:18
    Identity / metadata
    • Vendor: Generic → Unknown
    Settings (15)
    • bridge fan speed removed 100
    • close fan the first x layers removed 3
    • compatible printers added —
    • cooling 1 → 0
    • fan always on removed 0
    • fan cooling layer time removed 10
    • filament colour removed #29B2B2
    • filament cost added 0
    • filament density added 0
    • filament flow ratio 1 → 0.9
    • filament notes added —
    • filament vendor removed Generic
    • full fan speed layer removed 0
    • slow down layer time 5 → 20
    • slow down min speed 10 → 15
  60. via parent v10 of *common* — updated
    2026-05-19 05:18
    Identity / metadata
    • Vendor: Unknown → Generic
    Settings (15)
    • bridge fan speed added 100
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • cooling 0 → 1
    • fan always on added 0
    • fan cooling layer time added 10
    • filament colour added #29B2B2
    • filament cost removed 0
    • filament density removed 0
    • filament notes removed —
    • filament vendor added Generic
    • full fan speed layer added 0
    • slow down layer time 20 → 5
    • slow down min speed 15 → 10
  61. via parent v7 of *PLA* — updated
    2026-05-19 05:18
    Settings (20)
    • bridge fan speed 80 → 100
    • compatible printers added —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/ → printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • fan cooling layer time 15 → 100
    • fan max speed 80 → 100
    • fan min speed 40 → 100
    • filament colour #FF3232 → #DDDDDD
    • filament cooling moves removed 0
    • filament flow ratio 0.94 → 1
    • filament loading speed removed 30
    • filament loading speed start removed 30
    • filament max volumetric speed 0 → 15
    • filament ramming parameters removed 0
    • filament soluble added 0
    • filament unload time removed 0
    • filament unloading speed removed 30
    • filament unloading speed start removed 30
    • nozzle temperature 200 → 205
    • nozzle temperature initial layer 200 → 210
    • slow down layer time 10 → 20
  62. via parent v9 of *common* — updated
    2026-05-19 05:18
    Settings (6)
    • compatible printers added —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/ → printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
    • filament cost added 0
    • filament density added 0
    • filament soluble added 0
    • slow down layer time 10 → 20
  63. via parent v6 of *PLA* — updated
    2026-05-19 05:18
    Settings (21)
    • bridge fan speed 100 → 80
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ → printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/
    • fan cooling layer time 100 → 15
    • fan max speed 100 → 80
    • fan min speed 100 → 40
    • filament colour #DDDDDD → #FF3232
    • filament cooling moves added 0
    • filament flow ratio 1 → 0.94
    • filament loading speed added 30
    • filament loading speed start added 30
    • filament max volumetric speed 15 → 0
    • filament ramming parameters added 0
    • filament soluble removed 0
    • filament unload time added 0
    • filament unloading speed added 30
    • filament unloading speed start added 30
    • idle temperature removed 150
    • nozzle temperature 205 → 200
    • nozzle temperature initial layer 210 → 200
    • slow down layer time 20 → 10
  64. via parent v8 of *common* — updated
    2026-05-19 05:18
    Settings (6)
    • compatible printers removed —
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ → printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/
    • filament cost removed 0
    • filament density removed 0
    • filament soluble removed 0
    • slow down layer time 20 → 10
  65. via parent v5 of *PLA* — updated
    2026-05-19 05:17
    Settings (21)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/ → printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
    • filament colour #FF8000 → #DDDDDD
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 0 → 20
    • filament density 0 → 1.24
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • full fan speed layer removed 4
    • idle temperature added 150
    • nozzle temperature 210 → 205
    • nozzle temperature initial layer 215 → 210
    • slow down layer time 15 → 20
  66. via parent v7 of *common* — updated
    2026-05-19 05:17
    Settings (15)
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/ → printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
    • cooling 1 → 0
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • slow down layer time 15 → 20
  67. via parent v4 of *PLA* — updated
    2026-05-19 05:17
    Identity / metadata
    • Material: PLA,PLA → PLA
    Settings (35)
    • bridge fan speed 100,100 → 100
    • close fan the first x layers 1,1 → 1
    • compatible printers condition printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/ → printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/
    • cooling 1,1 → 1
    • fan always on 1,1 → 1
    • fan cooling layer time 100,100 → 100
    • fan max speed 100,100 → 100
    • fan min speed 100,100 → 100
    • filament colour #DDDDDD,#DDDDDD → #FF8000
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 20,20 → 0
    • filament density 1.24,1.24 → 0
    • filament diameter 1.75,1.75 → 1.75
    • filament flow ratio 1,1 → 1
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed 15,15 → 15
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament soluble 0,0 → 0
    • filament toolchange delay added 0
    • filament type PLA,PLA → PLA
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • full fan speed layer added 4
    • hot plate temp 60,60 → 60
    • hot plate temp initial layer 60,60 → 60
    • nozzle temperature 205,205 → 210
    • nozzle temperature initial layer 210,210 → 215
    • slow down layer time 20,20 → 15
    • slow down min speed 15,15 → 15
  68. via parent v6 of *common* — updated
    2026-05-19 05:17
    Identity / metadata
    • Vendor: QIDI → Unknown
    • Material: PLA → OTHER
    Settings (70)
    • bridge fan speed removed 100
    • chamber temperature removed 0
    • close fan the first x layers removed 1
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_SOVOL.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • cooling perimeter transition distance removed 3
    • cooling slowdown logic removed consistent_surface
    • disable rapid cooling fan first layers removed 3
    • enable advance pressure removed 1
    • enable auxiliary fan removed 100
    • enable auxiliary fan unseal removed 0
    • enable dynamic fan speeds removed 0
    • enable volume fan removed 100
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan always on removed 1
    • fan cooling layer time removed 60
    • fan max speed removed 100
    • fan min speed removed 100
    • filament colour removed #3399FF
    • filament cooling final speed 0 → 3.4
    • filament cooling initial speed 0 → 2.2
    • filament cooling moves 0 → 4
    • filament density 1.24 → 0
    • filament deretract speed removed nil
    • filament flow ratio 0.98 → 1
    • filament loading speed 0 → 28
    • filament loading speed start 0 → 3
    • filament max volumetric speed removed 20
    • filament minimal purge on wipe tower 5 → 15
    • filament multitool ramming removed 0
    • filament multitool ramming flow removed 10
    • filament multitool ramming volume removed 10
    • filament purge multiplier removed 100
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament shrink removed 100
    • filament spool weight removed 0
    • filament stamping distance removed 0
    • filament stamping loading speed removed 0
    • filament travel max lift removed nil
    • filament travel ramping lift removed nil
    • filament travel slope removed nil
    • filament type removed PLA
    • filament unloading speed 0 → 90
    • filament unloading speed start 0 → 100
    • filament vendor removed QIDI
    • filament wipe removed nil
    • filament wipe distance removed nil
    • full fan speed layer removed 0
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • idle temperature removed 100
    • nozzle temperature removed 220
    • nozzle temperature initial layer removed 210
    • overhang fan speed 0 removed 0
    • overhang fan speed 1 removed 0
    • overhang fan speed 2 removed 0
    • overhang fan speed 3 removed 0
    • seal print removed 1
    • slow down layer time 8 → 15
    • slow down min speed 20 → 15
    • start filament gcode removed ; Filament gcode M900 K0.02 T0.03
  69. via parent v5 of *common* — updated
    2026-05-19 05:15
    Identity / metadata
    • Vendor: Cocoa Press → QIDI
    • Material: OTHER → PLA
    Settings (54)
    • bridge fan speed 0 → 100
    • chamber temperature added 0
    • close fan the first x layers 3 → 1
    • compatible printers added —
    • compatible printers condition added —
    • compatible prints added —
    • compatible prints condition added —
    • cooling 0 → 1
    • cooling perimeter transition distance added 3
    • cooling slowdown logic added consistent_surface
    • disable rapid cooling fan first layers added 3
    • enable advance pressure added 1
    • enable auxiliary fan added 100
    • enable auxiliary fan unseal added 0
    • enable volume fan added 100
    • fan always on 0 → 1
    • fan min speed 35 → 100
    • filament colour #3D2113 → #3399FF
    • filament cooling final speed 3.4 → 0
    • filament cooling initial speed 2.2 → 0
    • filament cooling moves 4 → 0
    • filament cost 70 → 0
    • filament density 1.2912 → 1.24
    • filament diameter 22.66 → 1.75
    • filament flow ratio 1 → 0.98
    • filament loading speed 28 → 0
    • filament loading speed start 3 → 0
    • filament max volumetric speed 0 → 20
    • filament minimal purge on wipe tower 15 → 5
    • filament multitool ramming added 0
    • filament multitool ramming flow added 10
    • filament multitool ramming volume added 10
    • filament purge multiplier added 100
    • filament shrink added 100
    • filament stamping distance added 0
    • filament stamping loading speed added 0
    • filament travel max lift added nil
    • filament travel ramping lift added nil
    • filament travel slope added nil
    • filament type added PLA
    • filament unloading speed 90 → 0
    • filament unloading speed start 100 → 0
    • filament vendor Cocoa Press → QIDI
    • filament wipe 1 → nil
    • filament wipe distance added nil
    • hot plate temp 0 → 60
    • hot plate temp initial layer 0 → 60
    • idle temperature nil → 100
    • nozzle temperature added 220
    • nozzle temperature initial layer 0 → 210
    • seal print added 1
    • slow down layer time 5 → 8
    • slow down min speed 10 → 20
    • start filament gcode ; Filament gcode → ; Filament gcode M900 K0.02 T0.03
  70. via parent v4 of *common* — updated
    2026-05-19 05:14
    Identity / metadata
    • Vendor: Unknown → Cocoa Press
    Settings (55)
    • bridge fan speed added 0
    • close fan the first x layers added 3
    • compatible printers removed —
    • compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/
    • cooling 0,0 → 0
    • enable dynamic fan speeds added 0
    • end filament gcode added ; Filament-specific end gcode ;END gcode for filament
    • fan always on added 0
    • fan cooling layer time added 60
    • fan max speed added 100
    • fan min speed added 35
    • filament colour added #3D2113
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 0,0 → 70
    • filament density 0,0 → 1.2912
    • filament deretract speed added nil
    • filament diameter 1.75,1.75 → 22.66
    • filament flow ratio 1,1 → 1
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower added 15
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel added nil
    • filament retract before wipe added nil
    • filament retract layer change added nil
    • filament retract length added nil
    • filament retract lift added nil
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract restart extra added nil
    • filament retract speed added nil
    • filament soluble 0,0 → 0
    • filament spool weight added 0
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • filament vendor added Cocoa Press
    • filament wipe added 1
    • full fan speed layer added 0
    • hot plate temp added 0
    • hot plate temp initial layer added 0
    • idle temperature added nil
    • nozzle temperature initial layer added 0
    • overhang fan speed 0 added 0
    • overhang fan speed 1 added 0
    • overhang fan speed 2 added 0
    • overhang fan speed 3 added 0
    • slow down layer time 20,20 → 5
    • slow down min speed 15,15 → 10
    • start filament gcode added ; Filament gcode
  71. via parent v3 of *PLA* — updated
    2026-05-19 05:14
    Identity / metadata
    • Material: PLA → PLA,PLA
    Settings (49)
    • bridge fan speed 100 → 100,100
    • close fan the first x layers 1 → 1,1
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • cooling 1 → 1,1
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan always on 0 → 1,1
    • fan cooling layer time 600 → 100,100
    • fan max speed 100 → 100,100
    • fan min speed 100 → 100,100
    • filament colour #29B2B2 → #DDDDDD,#DDDDDD
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 24 → 20,20
    • filament density 0 → 1.24,1.24
    • filament deretract speed removed nil
    • filament diameter 1.75 → 1.75,1.75
    • filament flow ratio 0.92 → 1,1
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed 0 → 15,15
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament soluble 0 → 0,0
    • filament toolchange delay removed 0
    • filament type PLA → PLA,PLA
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • filament wipe removed nil
    • hot plate temp 60 → 60,60
    • hot plate temp initial layer 60 → 60,60
    • nozzle temperature 190 → 205,205
    • nozzle temperature initial layer 190 → 210,210
    • slow down layer time 1 → 20,20
    • slow down min speed 30 → 15,15
    • start filament gcode removed ; Filament gcode
  72. via parent v3 of *common* — updated
    2026-05-19 05:14
    Identity / metadata
    • Material: PLA → OTHER
    Settings (49)
    • bridge fan speed removed 100
    • close fan the first x layers removed 1
    • compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_LNL3D.*/
    • compatible prints removed —
    • compatible prints condition removed —
    • cooling 1 → 0,0
    • end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
    • fan always on removed 0
    • fan cooling layer time removed 600
    • fan max speed removed 100
    • fan min speed removed 100
    • filament colour removed #29B2B2
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 24 → 0,0
    • filament density 0 → 0,0
    • filament deretract speed removed nil
    • filament diameter 1.75 → 1.75,1.75
    • filament flow ratio 0.92 → 1,1
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed removed 0
    • filament minimal purge on wipe tower removed 15
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before travel removed nil
    • filament retract before wipe removed nil
    • filament retract layer change removed nil
    • filament retract length removed nil
    • filament retract lift removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract restart extra removed nil
    • filament retract speed removed nil
    • filament soluble 0 → 0,0
    • filament toolchange delay removed 0
    • filament type removed PLA
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • filament wipe removed nil
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • nozzle temperature removed 190
    • nozzle temperature initial layer removed 190
    • slow down layer time 1 → 20,20
    • slow down min speed 30 → 15,15
    • start filament gcode removed ; Filament gcode
  73. via parent v2 of *PLA* — updated
    2026-05-19 05:14
    Settings (13)
    • fan always on 1 → 0
    • fan cooling layer time 100 → 600
    • filament colour #DDDDDD → #29B2B2
    • filament cost 20 → 24
    • filament density 1.24 → 0
    • filament flow ratio 1 → 0.92
    • filament max volumetric speed 15 → 0
    • filament spool weight removed 0
    • full fan speed layer removed 0
    • nozzle temperature 205 → 190
    • nozzle temperature initial layer 210 → 190
    • slow down layer time 5 → 1
    • slow down min speed 10 → 30
  74. via parent v2 of *common* — updated
    2026-05-19 05:14
    Settings (12)
    • close fan the first x layers 2 → 1
    • fan always on 1 → 0
    • fan cooling layer time 60 → 600
    • fan min speed 35 → 100
    • filament cost 0 → 24
    • filament flow ratio 1 → 0.92
    • filament spool weight removed 0
    • full fan speed layer removed 0
    • nozzle temperature 210 → 190
    • nozzle temperature initial layer 210 → 190
    • slow down layer time 5 → 1
    • slow down min speed 10 → 30
  75. via parent v1 of *PLA* — created
    2026-05-19 05:14
    Profile created at this point. No prior version to diff against.
  76. via parent v1 of *common* — created
    2026-05-19 05:14
    Profile created at this point. No prior version to diff against.