Extrudr Flax @COREONE HF0.5

Extrudr · PLA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

→

Extrudr Flax @COREONE HF0.5

Includes (3)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: PLA inherited
Vendor: Extrudr inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.45 inherited
Cost (/kg): 50.91 inherited

Print temperature

Nozzle (initial layer) (°C): 190 inherited
Nozzle (other layers) (°C): 190 inherited
Chamber (°C): 20 via *PLA05HFC1*

Cooling

Fan minimum (%): 30 overridden
was 30 (inherited)
Fan maximum (%): 60 overridden
was 80 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 40 via *PLA05HFC1*
Slow down if layer below (sec): 11 via *PLA05HFC1*
Min speed when slowed (mm/s): 20 via *PLA05HFC1*

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 16 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 inherited	55 inherited

Other settings

bridge fan speed: 80 overridden
was 100 (inherited)
chamber minimal temperature: 0 via *PLA05HFC1*
compatible printers condition: printer_model=~/(COREONE|COREONEOAK|COREONEMMU3|COREONEL|COREONELMMU3)/ and nozzle_diameter[0]==0.5 and nozzle_high_flow[0] via *PLA05HFC1*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *PLA05HF*
cooling slowdown logic: consistent_surface via *PLA05HF*
enable dynamic fan speeds: 1 via *PLA05HFC1*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #FF3232 inherited
filament cooling final speed: 3.5 via *PLA05HF*
filament cooling initial speed: 10 via *PLA05HF*
filament cooling moves: 2 via *PLA05HF*
filament infill max crossing speed: 200 via *PLA05HF*
filament infill max speed: 250 via *PLA05HF*
filament load time: 10.9 via *PLA05HFC1*
filament loading speed: 10 via *PLA05HF*
filament loading speed start: 50 via *PLA05HF*
filament minimal purge on wipe tower: 15 via *PLA05HF*
filament notes: High Performance Filament for decorative parts. Prints as easily as PLA with much higher strength and temperature resistance. Fully biodegradable with a nice matt finish. https://www.extrudr.com/en/products/catalogue/?material=131 inherited
filament purge multiplier: 81.25% via *PLA05HF*
filament ramming parameters: 250 100 39.871 39.871| 0.05 39.9547 0.45 39.9547 0.95 39.9547 1.45 39.9547 1.95 39.9547 2.45 39.9547 2.95 39.9547 3.45 39.9547 3.95 39.9547 4.45 39.9547 4.95 39.9547 via *PLA05HF*
filament soluble: 0 inherited
filament spool weight: 262 inherited
filament stamping distance: 45 via *PLA05HF*
filament stamping loading speed: 29 via *PLA05HF*
filament toolchange delay: 0 via *PLA05HF*
filament travel max lift: 0.6 via *PLA05HF*
filament travel ramping lift: 1 via *PLA05HF*
filament travel slope: 1 via *PLA05HF*
filament unload time: 8.9 via *PLA05HFC1*
filament unloading speed: 40 via *PLA05HF*
filament unloading speed start: 30 via *PLA05HF*
full fan speed layer: 3 via *PLA05HF*
idle temperature: 170 via *PLA05HFC1*
overhang fan speed 0: 80 overridden
overhang fan speed 1: 0 overridden
start filament gcode: M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.036{elsif nozzle_diameter[filament_extruder_id]==0.5}0.026{elsif nozzle_diameter[filament_extruder_id]==0.6}0.022{elsif nozzle_diameter[filament_extruder_id]==0.8}0.015{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.08{else}0{endif} ; Filament gcode M142 S36 ; set heatbreak target temp via *PLA05HF*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "50.91"
  ],
  "filament_notes": [
    "High Performance Filament for decorative parts.\nPrints as easily as PLA with much higher strength and temperature resistance.\nFully biodegradable with a nice matt finish.\n\nhttps://www.extrudr.com/en/products/catalogue/?material=131"
  ],
  "filament_colour": [
    "#FF3232"
  ],
  "filament_vendor": [
    "Extrudr"
  ],
  "filament_density": [
    "1.45"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.9"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.9"
  ],
  "slow_down_layer_time": [
    "11"
  ],
  "start_filament_gcode": [
    "M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.036{elsif nozzle_diameter[filament_extruder_id]==0.5}0.026{elsif nozzle_diameter[filament_extruder_id]==0.6}0.022{elsif nozzle_diameter[filament_extruder_id]==0.8}0.015{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.08{else}0{endif} ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "2"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "40"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 39.871 39.871| 0.05 39.9547 0.45 39.9547 0.95 39.9547 1.45 39.9547 1.95 39.9547 2.45 39.9547 2.95 39.9547 3.45 39.9547 3.95 39.9547 4.45 39.9547 4.95 39.9547"
  ],
  "filament_cooling_final_speed": [
    "3.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_model=~/(COREONE|COREONEOAK|COREONEMMU3|COREONEL|COREONELMMU3)/ and nozzle_diameter[0]==0.5 and nozzle_high_flow[0]"
  ],
  "filament_max_volumetric_speed": [
    "16"
  ],
  "filament_cooling_initial_speed": [
    "10"
  ],
  "filament_unloading_speed_start": [
    "30"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_type": [
    "PLA"
  ],
  "hot_plate_temp": [
    "55"
  ],
  "bridge_fan_speed": [
    "80"
  ],
  "nozzle_temperature": [
    "190"
  ],
  "chamber_temperature": [
    "20"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "fan_cooling_layer_time": [
    "40"
  ],
  "chamber_minimal_temperature": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "nozzle_temperature_initial_layer": [
    "190"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_spool_weight": [
    "262"
  ],
  "idle_temperature": [
    "170"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "0.6"
  ],
  "filament_infill_max_speed": [
    "250"
  ],
  "filament_purge_multiplier": [
    "81.25%"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_stamping_loading_speed": [
    "29"
  ],
  "filament_infill_max_crossing_speed": [
    "200"
  ],
  "overhang_fan_speed_0": [
    "80"
  ],
  "overhang_fan_speed_1": [
    "0"
  ],
  "enable_dynamic_fan_speeds": [
    "1"
  ],
  "name": "Extrudr Flax @COREONE HF0.5",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:34